Home › View all posts by john › Page 17

Author: john

How to Replace a 2012 2013 2014 2015-2017 TOYOTA CAMRY EUR VERSION Car Radio Not Working with Aux Input Stereo Speaker Head Unit Effortlessly

Posted on by — No Comments ↓ 5,171 views
2012 2013 2014 2015-2017 TOYOTA CAMRY EUR VERSION Car Radio after installation

If you own a car, would you like to remove the factory radio and install the new car radio by yourself ? If yes, you can refer to a correct car radio installation instruction. Since most car radios are plug and play, the car radio removal and installation process is not complicated. The following is a 2012 2013 2014 2015-2017 TOYOTA CAMRY EUR VERSION car radio installation instruction from Seicane. If you have the same or similar dashboard, you can refer to this instruction carefully.

2012 2013 2014 2015-2017 TOYOTA CAMRY EUR VERSION Car Radio after installation
2012 2013 2014 2015-2017 TOYOTA CAMRY EUR VERSION Car Radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2012 2013 2014 2015-2017 TOYOTA CAMRY EUR VERSION car radio installation instruction

1. Remove the lower dashboard trim panels and the upper air conditioning vents.

Remove the lower dashboard trim panels and the upper air conditioning vents
Remove the lower dashboard trim panels and the upper air conditioning vents
1-1
1-1
1-2
1-2

2. Gently pry the upper dashboard housing from the radio’s trim bazel using either an automotive trim tool or your hands.

Gently pry the upper dashboard housing from the radio's trim bazel using either an automotive trim tool or your hands
Gently pry the upper dashboard housing from the radio’s trim bazel using either an automotive trim tool or your hands

3. After the upper dashboard housing has been disconnected, remove the two upper &two lower radio mounting screws from the dashboard.

After the upper dashboard housing has been disconnected, remove the two upper &two lower radio mounting screws from the dashboard
After the upper dashboard housing has been disconnected, remove the two upper &two lower radio mounting screws from the dashboard
3-1
3-1
3-2
3-2
3-3
3-3

4. Once the four radio mounting screws have been removed, gently lift the radio from the dashboard in order to gain access to the factory wiring harnesses on the backside.

Once the four radio mounting screws have been removed, gently lift the radio from the dashboard in order to gain access to the factory wiring harnesses on the backside
Once the four radio mounting screws have been removed, gently lift the radio from the dashboard in order to gain access to the factory wiring harnesses on the backside

5. Disconnect the connectors at the back of the radio.

6. Check all the accessories for the new Seicane car radio.

7. Connect the harnesses to the back of the new Seicane car radio.

8. Connect the Seicane car radio to your original radio’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

 

Wish you can get some help from the installation guide. If you meet any problems you don’t know how to solve by yourself, please don’t hesitate to contact your dealer, communicate with someone experienced or turn to a professional for help. Or if you still think it hard for you to install the new car radio by yourself, you’d better go to a car radio upgrade center and ask a professional technician to help you install the new car radio. Anyway, before installation, it is essential for you to select an ideal car radio. If you have no ideas, here I would like to share an amazing 2012 2013 2014 2015-2017 TOYOTA CAMRY EUR VERSION car radio from Seicane with you. For more details, please click:

https://www.seicane.com/android-hd-touchscreen-car-radio-dvd-player-for-2012-2017-toyota-camry-eur-version-gps-navigation-bluetooth-phone-music-wifi-support-obd2-usb-dab-mirror-link-steering-wheel-control-backup-camera-s23143e

This car radio is running on the stable and advanced Android 6.0 operation system and a powerful quad-core CPU processor to enhance its capabilities and improve performance. Therefore, with this car radio installed in your car, you can embrace a much smoother, faster and easier operation experience.

Even you don’t have good sense of directions, you can gain a lot of help from the 3D GPS navigation function. Thanks to the text-to-speech guidance provided by the high-end 3D GPS navigation system, you can easily know where you are and accurately find the right way to reach your desired destinations. Additionally, this unit’s dual zone function enables you to listen to your favorite music while navigating.

Through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, both Bluetooth hands-free phone calls and Bluetooth streaming music are available for you, which can add a lot of convenience and enjoyment too your driving.

If you like this unit, just add it to your shopping cart. Good luck!

How to Upgrade a 2008 2009 2010 2011 HONDA CIVIC RHD GPS Bluetooth DVD Car Radio

Posted on by — No Comments ↓ 4,513 views
2008 2009 2010 2011 HONDA CIVIC RHD GPS Bluetooth DVD Car Radio after installation

If you are fed up with your factory radio and plan to replace your factory radio with a new aftermarket car radio, you’d better find a related installation guide to help you with the installation. This article is mainly about how to remove the factory radio and install the new car radio for 2008 2009 2010 2011 HONDA CIVIC RHD. If you have the same or similar dashboard, you can refer to the following 2008 2009 2010 2011 HONDA CIVIC RHD car radio installation instruction.

2008 2009 2010 2011 HONDA CIVIC RHD GPS Bluetooth DVD Car Radio after installation
2008 2009 2010 2011 HONDA CIVIC RHD GPS Bluetooth DVD Car Radio after installation

Precautions for this installation:

1. Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2. Please make sure that all fastened wires are isolated with electrical tape.

3. Please make sure the ignition is off to avoid short circuit.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2008 2009 2010 2011 HONDA CIVIC RHD car radio installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Pry the cover of the slot below the CD player with a lever and remove it.

Pry the cover of the slot below the CD player with a lever and remove it
Pry the cover of the slot below the CD player with a lever and remove it

3. Remove two screws inside the slot with a ninety-degree screwdriver.

Remove two screws inside the slot with a ninety-degree screwdriver
Remove two screws inside the slot with a ninety-degree screwdriver

4. Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel.

Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel
Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel

5. Remove one screw in the dash.

Remove one screw in the dash
Remove one screw in the dash

6. Remove the vent panel.

Remove the vent panel
Remove the vent panel

7. Unplug the connectors beneath the panel.

Unplug the connectors beneath the panel
Unplug the connectors beneath the panel

8. Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash.

Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash
Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash

9. Unplug the connectors at the back of the original radio.

Unplug the connectors at the back of the original radio
Unplug the connectors at the back of the original radio
9-1
9-1

10. Disconnect the antenna and the other connector on the other side of the original radio.

Disconnect the antenna and the other connector on the other side of the original radio
Disconnect the antenna and the other connector on the other side of the original radio

11. Check all the accessories for the new Seicane car stereo.

12. Connect the harnesses to the back of the new Seicane car stereo.

13. Connect the Seicane car stereo to your original car radio’s plugs.

14. Put the new Seicane car stereo into the dash.

15. Turn on the new Seicane car stereo and check whether the unit is working properly.

 

Wish you can learn some skills from the above installation steps. If you meet any difficulties, you can contact your dealer, communicate with someone experienced or turn to a professional for help. Or if you are afraid of making damage to either your car radio or your car, you can directly arrange a professional technician to help you install the new car radio. Anyway, before installation, it is essential for you to pick an ideal car radio for your beloved car radio. If you have no ideas, here I would like to recommend a remarkable 2008 2009 2010 2011 HONDA CIVIC RHD car radio from Seicane to you. For more details, please click:

https://www.seicane.com/android-hd-touchscrenn-car-radio-head-unit-for-2008-2009-2010-2011-honda-civic-rhd-dvd-player-gps-navigation-bluetooth-wifi-support-mirror-link-usb-dvr-1080p-video-steering-wheel-control-s23307e

This car radio is running on the advanced and stable Android 6.0 operation system and a powerful quad-core CPU processor as well as 2GB RAM, so you are going to have a much smoother, faster and easier operation experience.

Thanks to the turn-by-turn direction and voice prompts provided by the high-end 3D GPS navigation system, you are able to easily and quickly locate where you are and navigate to any locations you would like to go to. Besides, this car radio comes with dual zone function, which enables you to listen to your favorite music while navigating.

Besides, with built-in Bluetooth module, this unit enables you to pair your Bluetooth-enabled mobile phone with this car radio, so you can dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone music playlist.

What are you waiting for? If you like this unit, you can add this car radio to your shopping cart. Good luck!

Special Tips to Properly Replace a 2008 2009 2010 2011 2012-2013 PEUGEOT 3008 Car Stereo with DVD Player Bluetooth GPS Navigation System

Posted on by — 2 Comments ↓ 10,170 views
2008 2009 2010 2011 2012-2013 PEUGEOT 3008 Car Stereo after installation

If you would like to enjoy a wide range of upgraded and modern features so as to gain more convenience and enjoyment to enrich your in-car life, you can consider replacing your factory radio with a new aftermarket car radio. Since most car radios are plug and play, the installation is not complicated, you can find a related installation guide and follow it to deal with the new car radio installation. The following is a 2008 2009 2010 2011 2012-2013 PEUGEOT 3008 car radio installation instruction from Seicane. If you have the same or similar dashboard, please refer to this instruction.

2008 2009 2010 2011 2012-2013 PEUGEOT 3008 Car Stereo after installation
2008 2009 2010 2011 2012-2013 PEUGEOT 3008 Car Stereo after installation

Precautions for this installation:

1. Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2. Please make sure that all fastened wires are isolated with electrical tape.

3. Please make sure the ignition is off to avoid short circuit.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2008 2009 2010 2011 2012-2013 PEUGEOT 3008 car radio installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Prepare a pair of DIN style release keys.

Prepare a pair of DIN style release keys
Prepare a pair of DIN style release keys

3. Insert the release keys into the removal slots of the radio.

Insert the release keys into the removal slots of the radio
Insert the release keys into the removal slots of the radio
3-1
3-1

4. Pull outwards to release the radio.

Pull outwards to release the radio
Pull outwards to release the radio

5. Disconnect the connectors at the back of the radio.

Disconnect the connectors at the back of the radio
Disconnect the connectors at the back of the radio

6. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo
Check all the accessories for the new Seicane car stereo

7. Connect the harnesses to the back of the new Seicanecar stereo.

Connect the harnesses to the back of the new Seicanecar stereo
Connect the harnesses to the back of the new Seicanecar stereo

8. Connect the Seicane car stereo to your original stereo’s plugs.

9. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car stereo into the dash.

11. Put everything into their original place. All the installation is done.

 

Wish you can learn some skills from the above installation guide. If you have any problems, you can contact your dealer, communicate with someone experienced or turn to a professional for help. Or you can directly go to a car radio upgrade center to ask a professional technician to help you install the new car radio. Anyway, before installation, it is essential for you to select an ideal car radio for your car. If you have no ideas, you can check out the following link which is a 2008 2009 2010 2011 2012-2013 PEUGEOT 3008 car radio from Seicane. For more details, please click:

https://www.seicane.com/android-touchscreen-2008-2013-peugeot-3008-radio-dvd-gps-navigation-system-with-wifi-bluetooth-steering-wheel-control-obd2-dab-dvr-aux-backup-camera-mirror-link-s32738f

This car radio is upgraded to the most advanced Android 7.1 operation system and a powerful quad-core CPU processor, so it can facilitate the operation and provide its users with a much smoother and faster operation experience.

After you get this car radio installed in your car, you will be able to get access to a wide range of comprehensive features, mainly including 3D GPS navigation system, FM/AM radio tuner, DVD player, Bluetooth hands-free phone calls, Bluetooth streaming music, AUX, steering wheel control, USB & SD card connection, etc.

With the assistance of the high-end 3D GPS navigation system, you can easily know where you car now and accurately get to any locations you would like to go to according to turn-by-turn directions and voice prompts. Additionally, this unit comes with dual zone function which enables you to listen to your favorite music while navigating, and the music will automatically switch to GPS voice.

Moreover, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, you can freely get access to both Bluetooth hands-free phone calls as well as Bluetooth streaming music while navigating.

If you like this unit, just add it to your shopping cart. Good luck to you!

A Detailed Instruction on a 2007 2008 2009 2010 2011-2012 Hyundai H1 GPS Bluetooth DVD Car Radio Upgrade

Posted on by — No Comments ↓ 3,959 views
2007 2008 2009 2010 2011-2012 Hyundai H1 GPS Bluetooth DVD Car Radio after installation

Nowadays, there is a trend that more and more car owners would like to replace their factory radio with a new aftermarket car radio. If you have a 2007 2008 2009 2010 2011-2012 Hyundai H1 and want to upgrade your factory radio’s capabilities, then you can find a correct installation guide to help with the installation of your new car radio. This article mainly aims to introduce a detailed 2007 2008 2009 2010 2011-2012 Hyundai H1 car radio installation instruction from Seicane to you. If you have the same or similar dashboard, the following installation guide from Seicane will be helpful for you.

2007 2008 2009 2010 2011-2012 Hyundai H1 GPS Bluetooth DVD Car Radio after installation
2007 2008 2009 2010 2011-2012 Hyundai H1 GPS Bluetooth DVD Car Radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

2007 2008 2009 2010 2011-2012 Hyundai H1 car radio installation instruction

1. Pry the plastic panel with a removal tool.

Pry the plastic panel with a removal tool
Pry the plastic panel with a removal tool

2. Remove the panel, and disconnect the connectors at the back of the panel.

Remove the panel, and disconnect the connectors at the back of the panel
Remove the panel, and disconnect the connectors at the back of the panel

3. Unscrew three screws securing the panel with a screwdriver.

Unscrew three screws securing the panel with a screwdriver
Unscrew three screws securing the panel with a screwdriver
3-1
3-1

4. Pry the trim panel shown as below with a removal tool.

Pry the trim panel shown as below with a removal tool
Pry the trim panel shown as below with a removal tool
4-1
4-1

5. Remove the trim panel, then disconnect the connectors at the back of the panel.

Remove the trim panel, then disconnect the connectors at the back of the panel
Remove the trim panel, then disconnect the connectors at the back of the panel

6. Unscrew all screws securing the original head unit with a screwdriver.

Unscrew all screws securing the original head unit with a screwdriver
Unscrew all screws securing the original head unit with a screwdriver

7. Gently take the factory radio out of the dashboard.

8. Disconnect all connectors at the back of the original car radio.

9. Check all the accessories for the new Seicane car radio.

10. Connect the harnesses to the back of the new Seicane car radio.

11. Connect the Seicane car radio to your original radio’s plugs.

12. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

13. Put the new Seicane car radio into the dash.

14. Put everything into their original place. All the installation is done.

 

Now do you have a general understanding of the above installation instruction? If you have any doubts, you may browse some professional websites. Besides, please don’t hesitate to consult your dealer, communicate with someone experienced or seek help from a professional. If you still think it hard for you to install the new car radio by yourself, you’d better straightly go to a car radio upgrade center to ask a technician to help you.

What’s more, is you are still looking for a suitable car radio but don’t know what kind of car radios can fit your car well, you might as well check out the following link which is a 2007 2008 2009 2010 2011-2012 Hyundai H1 car radio from Seicane.

https://www.seicane.com/android-2007-2008-2009-2012-hyundai-h1-bluetooth-radio-gps-navigation-dvd-player-support-aux-rearview-camera-mirror-link-usb-sd-dvr-wifi-obd2-audio-system-s32542f

Loaded with the most stable and advanced Android 7.1.1 operation system and a powerful quad-core CPU processor, this car radio can provide its users with higher capabilities and better performance.

When you are driving around an unfamiliar place, even you are not good at identifying directions, you can make full use of the high-accuracy 3D GPS navigation system to locate where you are and navigate to your desired destinations through turn-by-turn directions and voice prompts. And with dual zone function, this car radio enables you to listen to your favorite music while navigating, which can add a lot of fun to your driving.

And for more entertainment, you can turn on this unit’s DVD player function to play amazing videos, TV programs, movies, etc. Thus, you can get a lot of fun while driving.

If you like this car radio, just add it to your shopping cart. Good luck to you!

How to Upgrade a 2013 2014 2015 2016 Toyota RAV4 Car Stereo with DVD player GPS Navigation System

Posted on by — 2 Comments ↓ 7,959 views
2013 2014 2015 2016 Toyota RAV4 Car Stereo after installation

An ideal car radio plays a very important role in a car since it can help bring great convenience and entertainment all the way. If you are fed up with your factory radio due to its simple functions, you can think about replacing it with a brand new multifunctional car radio. If you own a 2013 2014 2015 2016 Toyota RAV4 and plan to upgrade your factory radio, you can refer to the following 2013 2014 2015 2016 Toyota RAV4 car radio installation instruction from Seicane. Wish you can get some help from this instruction.

2013 2014 2015 2016 Toyota RAV4 Car Stereo after installation
2013 2014 2015 2016 Toyota RAV4 Car Stereo after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2013 2014 2015 2016 Toyota RAV4 car radio installation instruction

1. Using a plastic removal tool to remove the upper dashboard trim panel. Set the panel aside once removed.

Using a plastic removal tool to remove the upper dashboard trim panel. Set the panel aside once removed
Using a plastic removal tool to remove the upper dashboard trim panel. Set the panel aside once removed

2. Gently pry the air conditioning vents on the left and right-hand sides of the factory radio away from the dashboard.

Gently pry the air conditioning vents on the left and right-hand sides of the factory radio away from the dashboard
Gently pry the air conditioning vents on the left and right-hand sides of the factory radio away from the dashboard
2-1
2-1

3. Gently pry the clock display and hazard lamp panel away from the dashboard and set it to the side.

Gently pry the clock display and hazard lamp panel away from the dashboard and set it to the side
Gently pry the clock display and hazard lamp panel away from the dashboard and set it to the side

4. Remove the four retaining screws attaching the factory radio to the dashboard.

Remove the four retaining screws attaching the factory radio to the dashboard
Remove the four retaining screws attaching the factory radio to the dashboard

5. Gently lift the touch screen unit away from the dashboard and lean it to gain access to the wiring harness on the reverse side.

Gently lift the touch screen unit away from the dashboard and lean it to gain access to the wiring harness on the reverse side
Gently lift the touch screen unit away from the dashboard and lean it to gain access to the wiring harness on the reverse side

6. Disconnect the factory radio by unplugging the individual harnesses.

Disconnect the factory radio by unplugging the individual harnesses
Disconnect the factory radio by unplugging the individual harnesses

7. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo
Check all the accessories for the new Seicane car stereo

8. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo
Connect the harnesses to the back of the new Seicane car stereo

9. Connect the Seicane car stereo to your original stereo’s plugs.

10. Turn on the new Seicane car stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car stereo into the dash.

12. Put everything into their original place. All the installation is done.

 

Don’t worry if you encounter any problems during the installation. To solve these problems, you can not only contact your dealer for a wiring diagram but also turn to a professional for help. Besides, if you still think it hard for you to install the new car radio, you can directly arrange a professional technician to help you. Anyway, it is essential for you to select an ideal car radio. If you have no ideas, you can check out the following link which is a remarkable 2013 2014 2015 2016 Toyota RAV4 car radio from Seciane.

https://www.seicane.com/autoradio-android-gps-navigation-system-for-2013-2016-toyota-rav4-with-dvd-player-bluetooth-mirror-link-capacitive-multi-touch-screen-obd-dvr-tv-usb-sd-3g-wifi-rear-view-camera-s168017

This car radio is loaded with the latest and stable Android 7.1 operation system and a high-quality quad-core CPU processor to enhance its capabilities and improve its performance.

With the assistance of the high-end 3D GPS navigation system of this unit, you can easily locate where you are and find the right way to reach any locations you would like to go to according to turn-by-turn directions and voice prompts. And this unit’s dual zone function enables you to freely listen to your favorite music while navigating.

Additionally, by paring your Bluetooth-enabled mobile phone and this car radio, you can dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your mobile phone playlists. Therefore, you will get great convenience and enjoyment.

Wish you like this unit and enjoy your in-car life accompanied by this unit. Good luck to you!

How to Install a 2014 2015 KIA K5 OPTIMA Car Stereo with Bluetooth GPS Navigation System

Posted on by — 4 Comments ↓ 12,104 views
2014 2015 KIA K5 OPTIMA Car Stereo after installation

If you find your factory radio is too outdated to support a wide range of practical and entertainment features, it will be very wise of you to replace your factory radio with a new multifunctional car radio. With an ideal car radio installed in your car, you can have a more convenient and comfortable car interior environment as well as a more relaxing driving experience. The following is an installation guide for a 2014 2015 KIA K5 OPTIMA car radio. If you have the same or similar dashboard, you can refer to the following guide.

2014 2015 KIA K5 OPTIMA Car Stereo after installation
2014 2015 KIA K5 OPTIMA Car Stereo after installation

Precautions for this installation:

1. Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2. Please make sure that all fastened wires are isolated with electrical tape.

3. Please make sure the ignition is off to avoid short circuit.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2014 2015 KIA K5 OPTIMA car radio installation guide

1. Remove the panels shown as the pictures below, then set them aside.

Remove the panels shown as the pictures below, then set them aside
Remove the panels shown as the pictures below, then set them aside
1-1
1-1
1-2
1-2

2. Unscrew all the screws as the pictures below with a screwdriver.

Unscrew all the screws as the pictures below with a screwdriver
Unscrew all the screws as the pictures below with a screwdriver
2-1
2-1
2-2
2-2
2-3
2-3
2-4
2-4
2-5
2-5
2-6
2-6
2-7
2-7
2-8
2-8
2-9
2-9
2-10
2-10
2-11
2-11
2-12
2-12
2-13
2-13

3. Take out the air conditioner control.

Take out the air conditioner control
Take out the air conditioner control

4. Unscrew all the screws holding the air conditioner vent with a screwdriver.

Unscrew all the screws holding the air conditioner vent with a screwdriver
Unscrew all the screws holding the air conditioner vent with a screwdriver

5. Remove the air conditioner vent.

Remove the air conditioner vent
Remove the air conditioner vent

6. Unscrew four screws holding the original car radio with a screwdriver.

Unscrew four screws holding the original car radio with a screwdriver
Unscrew four screws holding the original car radio with a screwdriver
6-1
6-1
6-2
6-2

7. Gently take the original car radio out of the dash.

Gently take the original car radio out of the dash
Gently take the original car radio out of the dash

8. Disconnect all connectors at the back of the original car radio.

9. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

10. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

11. Connect the Seicane car radio to your original car radio ‘s plugs.

12. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

13.Put the new Seicane car radio into the dash.

14. Put everything into their original place. All the installation is done.

 

Now do you have a general understanding of the 2014 2015 KIA K5 OPTIMA car radio installation? If no, you can browse some professional websites. Or you can contact your dealer, communicate with someone experienced or turn to a professional for help. If you are afraid of making damage to either your car radio or your car, you can straightly go to a car radio upgrade center and ask a professional technician to help you install the new car radio. Any way, before installation, it is essential for you to select a suitable car radio from Seicane. Here I would like to share an amazing 2014 2015 KIA K5 OPTIMA car radio from Seicane with you. For more details, please click:

https://www.seicane.com/android-radio-gps-navigation-system-for-2014-2015-kia-k5-optima-with-hd-touch-screen-dvd-player-bluetooth-obd2-dvr-rearview-camera-tv-1080p-video-3g-wifi-steering-wheel-control-usb-sd-mirror-link-s168043

Loaded with the stable and latest Android 7.1 operation system, a powerful quad-core CPU processor and 2GB RAM, this all-in-one car radio can be regarded as one of the replacements for your factory radio.

Under the guidance of the turn-by-turn directions and voice prompts provided by the worldwide real-time GPS navigation system of high accuracy, you are able to easily and quickly know your current locations and find the most suitable way to get to your destinations. And with dual zone function, this unit makes it possible for you to listen to your favorite music under GPS mode, and the music will automatically switch to GPS voice.

Besides, through the Bluetooth connection between your Bluetooth-enabled mobile phone with this advanced car radio, you are able to dial, answer, reject and mute Bluetooth hands-free phone calls and listen to Bluetooth streaming music without taking hands off the steering wheel.

What’s more, you can turn on this unit’s function as a DVD player to play music, videos, TV programs, movies, etc to relax both yourself and your passengers. Therefore, you can gain greatest convenience and enjoyment.

Wish you like this unit and good luck to you!

How to Quickly Upgrade a 2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica Car Radio with DVD Player GPS Navigation System

Posted on by — No Comments ↓ 3,741 views
2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica Car Radio after installation

As for car owners, it will be very wonderful if they can enjoy the greatest convenience and entertainment in car as well as have a comfortable and relaxing in-car experience. If you are also desired to have both convenient and relaxing in-car life, you might as well replace your factory radio with a new aftermarket radio. The following is a 2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica car radio installation instruction which can be taken as a reference.

2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica Car Radio after installation
2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica Car Radio after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica car radio installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Grab at the bottoming plastic cover, push the bottoming box and release it.

Grab at the bottoming plastic cover, push the bottoming box and release it
Grab at the bottoming plastic cover, push the bottoming box and release it

3. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside
Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside
3-1
3-1

4. Unplug the connectors at the back of panel.

Unplug the connectors at the back of panel
Unplug the connectors at the back of panel

5. Remove four screws that fixed the radio on the dashboard.

Remove four screws that fixed the radio on the dashboard
Remove four screws that fixed the radio on the dashboard
5-1
5-1
5-2
5-2
5-3
5-3

6. Gently pull the factory radio out of the dash. Then unplug the connectors at the back of the factory radio.

Gently pull the factory radio out of the dash. Then unplug the connectors at the back of the factory radio
Gently pull the factory radio out of the dash. Then unplug the connectors at the back of the factory radio
6-1
6-1

7. Check all the accessories for the new Seicane head unit.

Check all the accessories for the new Seicane head unit
Check all the accessories for the new Seicane head unit

8. Connect the harnesses to the back of the new Seicane head unit.

Connect the harnesses to the back of the new Seicane head unit
Connect the harnesses to the back of the new Seicane head unit

9. Connect the Seicane head unit to your original head unit ‘s plugs.

10. Turn on the new Seicane head unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane head unit into the dash.

12. Put everything into their original place. All the installation is done.

 

Wish the above installation guide can be helpful for you. If you meet any difficulties, please don’t be worried. To overcome these difficulties, you can seek help from your dealer, someone experienced or a professional. If you still think it hard for you to install the new car radio by yourself, you can straightly arrange a technician to help you.

While for the selection of an ideal car radio for your car, if you have no ideas, you can check out the following link which is a remarkable 2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica  car radio from Seicane.

https://www.seicane.com/2006-2011-chevy-chevrolet-epica-android-aftermarket-radio-gps-touch-screen-navigation-system-dvd-player-bluetooth-mirror-link-obd2-dvr-rearview-camera-tv-usb-sd-3g-wifi-ipod-1080p-video-steering-wheel-control-s166235

This car radio runs on the latest Android 7.1 operation system and a powerful quad-core CPU processor to enhance its capabilities and performance. With this car radio installed in your car, you can get access to comprehensive functions and features in diverse, mainly including 3D GPS navigation system, FM/AM radio, Bluetooth hands-free phone calls, Bluetooth streaming music, DVD player, file management, USB or SD card connection, etc.

Thanks to turn-by-turn directions and voice prompts provided by GPS function, you can easily know your current locations and find the most suitable way to arrive at your destinations. And this unit’s dual zone function enables you to listen to your favorite music while navigating, which won’t have any negative influence on GPS function.

Wish you like this modern car radio. Good luck to you.

How to Replace a 2008 2009 2010 Jeep Commander Car Radio with Stereo Audio Speakers in a Quick Way

Posted on by — 4 Comments ↓ 6,445 views
2008 2009 2010 Jeep Commander Car Radio after installation

If you are an owner of a 2008 2009 2010 Jeep Commander and happen to plan to replace your factory radio with a brand new multifunctional car radio, you may need a correct installation instruction to help you. This article is mainly about a 2008 2009 2010 Jeep Commander car radio installation instruction, which may help you gain a general understanding of the old radio removal and the new car radio installation. Wish it is helpful for you to some extent.

2008 2009 2010 Jeep Commander Car Radio after installation
2008 2009 2010 Jeep Commander Car Radio after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2008 2009 2010 Jeep Commander car radio installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Remove the panel by prying the edges with a lever.

Remove the panel by prying the edges with a lever
Remove the panel by prying the edges with a lever

3. Unscrew four screws holding the original radio in place with a screwdriver.

Unscrew four screws holding the original radio in place with a screwdriver
Unscrew four screws holding the original radio in place with a screwdriver

4. Take the original radio out of the dash.

Take the original radio out of the dash
Take the original radio out of the dash

5. Disconnect the connectors at the back of the original radio.

Disconnect the connectors at the back of the original radio
Disconnect the connectors at the back of the original radio

6. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo
Check all the accessories for the new Seicane car stereo

7. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo
Connect the harnesses to the back of the new Seicane car stereo

8. Connect the Seicane car stereo to your original car radio’s plugs.

9. Turn on the new Seicane stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane stereo into the dash.

11. Put everything into their original place.

 

Wish the above installation steps can be helpful for you to some extent. If you meet any problems and don’t know how to deal with, you can seek help from your dealer, someone experienced or a professional. Anyway, before installation, it is crucial to select an ideal car radio. If you don’t know which kind of car radio can fit your car well, you can check out the following link which is an excellent 2008 2009 2010 Jeep Commander car radio from Seicane.

https://www.seicane.com/android-radio-2008-2009-2010-jeep-commander-gps-navigation-bluetooth-usb-wifi-dvd-player-support-1080p-video-dvr-obd2-rearview-camera-steering-wheel-control-s6933

With this car radio installed in your car, you will able to embrace a smoother, easier and faster operation experience since this car radio runs on the advanced and stable Android 7.1 operation system and a powerful quad-core CPU processor to enhance and improve its capabilities and performance.

The worldwide real-time GPS navigation system is especially built in this car radio, so you don’t need to worry about getting lost any more even you have no good sense of directions. Through the turn-by-turn directions and voice prompts, you are able to easily know your current locations and find the most suitable way to reach your desired destinations.

Additionally, under Bluetooth technology, you are able to connect your Bluetooth-enabled mobile phone to this car radio so as to get access to Bluetooth hands-free phone calls for convenience and Bluetooth streaming music for enjoyment. Thus, you will gain a safer, more convenient and relaxing driving.

If you like this unit, just add it to your shopping cart right now. Good luck to you!

How to Remove a 2010 2011 2012 2013 Mazda 5/Premacy Car Radio to Install a Touch Screen Radio Stereo Navigation System

Posted on by — 2 Comments ↓ 6,477 views
2010 2011 2012 2013 Mazda 5 Premacy Car Radio after installation

There is no doubt that to have both a comfortable car interior environment and a relaxing driving experience is what most car owners are pursuing at present. And to achieve that goal, it is wise of you to think about replacing your factory radio with a new aftermarket car radio. The following is a 2010 2011 2012 2013 Mazda 5/Premacy car radio installation guide. If you have the same or similar dashboard, you can refer to the following guide and take it as a reference.

2010 2011 2012 2013 Mazda 5 Premacy Car Radio after installation
2010 2011 2012 2013 Mazda 5 Premacy Car Radio after installation

Here are some tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and www.seicane.com make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd- 400

2010 2011 2012 2013 Mazda 5/Premacy car radio installation guide

1. Unclip and remove the cup holder panel in the center console.

Unclip and remove the cup holder panel in the center console
Unclip and remove the cup holder panel in the center console
1-1
1-1

2. Unclip and remove the small pocket panel on the back of the center console behind shifter.

Unclip and remove the small pocket panel on the back of the center console behind shifter
Unclip and remove the small pocket panel on the back of the center console behind shifter
2-1
2-1
2-2
2-2

3. Remove two 8mm bolts under the cup holder panel holding the back half of the center console to the front half.

Remove two 8mm bolts under the cup holder panel holding the back half of the center console to the front half
Remove two 8mm bolts under the cup holder panel holding the back half of the center console to the front half

4. Unscrew the shift knob and remove it carefully.

Unscrew the shift knob and remove it carefully
Unscrew the shift knob and remove it carefully

5. Unclip and remove the shifter trim panel.

Unclip and remove the shifter trim panel
Unclip and remove the shifter trim panel

6. Slide both seats forwards and remove two Phillips screws on each side of the center console under the screw covers.

Slide both seats forwards and remove two Phillips screws on each side of the center console under the screw covers
Slide both seats forwards and remove two Phillips screws on each side of the center console under the screw covers
6-1
6-1

7. Unclip and pull back the panels at the lower front sides of the center console.

Unclip and pull back the panels at the lower front sides of the center console
Unclip and pull back the panels at the lower front sides of the center console

8. Remove two Phillips screws from both sides(total of four) of the front lower half of the center console.

Remove two Phillips screws from both sides(total of four) of the front lower half of the center console
Remove two Phillips screws from both sides(total of four) of the front lower half of the center console
8-1
8-1

9. Unclip and remove the vent panel including the hazard switch above the factory radio. Then it will be much easier for you to get access to the screws. And remove the two screws.

Unclip and remove the vent panel including the hazard switch above the factory radio. Then it will be much easier for you to get access to the screws. And remove the two screws
Unclip and remove the vent panel including the hazard switch above the factory radio. Then it will be much easier for you to get access to the screws. And remove the two screws
9-1
9-1
9-2
9-2

10. Remove two screws from behind the shifter trim.

Remove two screws from behind the shifter trim
Remove two screws from behind the shifter trim
10-1
10-1

11. Pull center console forward so as to gain access to two screws under the climate controls. And then remove these two screws.

Pull center console forward so as to gain access to two screws under the climate controls. And then remove these two screws
Pull center console forward so as to gain access to two screws under the climate controls. And then remove these two screws
11-1
11-1

12. Unclip harness and pull rear center console backwards.

Unclip harness and pull rear center console backwards
Unclip harness and pull rear center console backwards

13. Press in shifter to release trigger and pull shifter down, make sure to have a brake on.

Press in shifter to release trigger and pull shifter down, make sure to have a brake on
Press in shifter to release trigger and pull shifter down, make sure to have a brake on

14. Use a pry tool to release climate controls.

Use a pry tool to release climate controls
Use a pry tool to release climate controls

15. Remove one screw and one 10mm bolt.

Remove one screw and one 10mm bolt
Remove one screw and one 10mm bolt

16. Pull factory radio out, release clips and unplug radio connectors.

Pull factory radio out, release clips and unplug radio connectors
Pull factory radio out, release clips and unplug radio connectors

17. Check all the accessories for the new Seicane car radio.

18. Connect the harnesses to the back of the new Seicane car radio.

19. Connect the Seicane car radio to your original car radio ‘s plugs.

20. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

21. Put the new Seicane radio into the dash.

22. Put everything into their original place. All the installation is done.

 

Now do you have a general understanding of 2010 2011 2012 2013 Mazda 5/Premacy car radio installation? If not, please feel free to seek advice from your dealer, communicate with someone experienced or turn to a professional for help. Or you can directly arrange a professional technician to help you install the new car radio. Anyway, before installation, please do select an ideal car radio. If you have no ideas, you can refer to the following link which is an amazing 2010 2011 2012 2013 Mazda 5/Premacy car radio from Seicane.

https://www.seicane.com/hd-touchscreen-android-gps-navigation-car-radio-dvd-player-for-2010-2013-mazda-5-premacy-with-bluetooth-canbus-usb-wifi-obd2-dvr-aux-mirror-link-steering-wheel-control-s18m015

This car radio comes with a wide range of practical and entertainment features to meet your different needs in car. So it can be regarded as one of the best choices to replace your factory radio.

After you get this car radio installed in your car, you can make full use of its built-in GPS navigation system of high accuracy. Through the text-to-speech guidance, you can easily locate where you are and accurately navigate to any locations you would like to go to.

Besides, as long as you connect your Bluetooth-enabled mobile phone to this unit through Bluetooth connection, you can dial, answer, reject or mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music without taking your hands off the steering wheel.

If you like this unit, just add it to your shopping cart. Good luck!

How to Effectively Replace a 2015 2016 2017 JEEP Wrangler Car Radio with DVD Player Bluetooth GPS Navigation System

Posted on by — No Comments ↓ 5,683 views
2015 2016 2017 JEEP Wrangler Car Radio after installation

Would you like to enjoy more up-to-date features brought by an ideal car radio in your car while you are driving? If yes, why not think about replacing your factory radio with a new multifunctional car radio. If you have a 2015 2016 2017 JEEP Wrangler and plan to install a new aftermarket car radio so as to embrace a brand new driving experience, then you can take the following related installation guide as a reference. Wish you can get some help from the guide.

2015 2016 2017 JEEP Wrangler Car Radio after installation
2015 2016 2017 JEEP Wrangler Car Radio after installation

Tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2015 2016 2017 JEEP Wrangler car radio installation instruction

1. Get the window control out of the original place, so that you can get access to the screw that is behind it.

Get the window control out of the original place, so that you can get access to the screw that is behind it
Get the window control out of the original place, so that you can get access to the screw that is behind it

2. Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control.

Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control
Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control
2-1
2-1

3. You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out.

You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out
You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out
3-1
3-1

4. There is a clip and you need to push it down and make it come right off, after that, put this window control to the side.

There is a clip and you need to push it down and make it come right off, after that, put this window control to the side
There is a clip and you need to push it down and make it come right off, after that, put this window control to the side
4-1
4-1
4-2
4-2
4-3
4-3

5. Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray.

Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray
Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray
5-1
5-1
5-2
5-2

6. Next you are going to pull away the trim under the steering wheel.

Next you are going to pull away the trim under the steering wheel
Next you are going to pull away the trim under the steering wheel
6-1
6-1

7. With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set.

With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set
With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set

8. Firmly pull the dash and it should be clipped out.

Firmly pull the dash and it should be clipped out
Firmly pull the dash and it should be clipped out
8-1
8-1

9. With the dash removed, you now can have access to the four bolts that are holding the original car radio.

With the dash removed, you now can have access to the four bolts that are holding the original car radio
With the dash removed, you now can have access to the four bolts that are holding the original car radio

10. Remove these four bolts with the seven millimeter screwdriver.

Remove these four bolts with the seven millimeter screwdriver
Remove these four bolts with the seven millimeter screwdriver

11. With all the bolts removed, the original car radio should simply slide out from the original place.

With all the bolts removed, the original car radio should simply slide out from the original place
With all the bolts removed, the original car radio should simply slide out from the original place
11-1
11-1

12. Disconnect the factory connectors and wires at the back of the original car radio.

Disconnect the factory connectors and wires at the back of the original car radio
Disconnect the factory connectors and wires at the back of the original car radio

13. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

14. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

15. Connect the Seicane car radio to your original radio’s plugs.

16. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

17. Put the new Seicane car radio into the dash.

18. Put everything into their original place. All the installation is done.

 

Above is the whole removal and installation process for a 2015 2016 2017 JEEP Wrangler. If you have any doubts, please don’t hesitate to seek help from your dealer, someone experienced or a professional. Besides, it is essential for you to pick an ideal car radio for your car. If you have no ideas, here I would like to recommend a remarkable 2015 2016 2017 JEEP Wrangler car radio from Seicane to you. For more details, please click:

https://www.seicane.com/en/android-touchscreen-radio-for-2015-2017-jeep-wrangler-bluetooth-music-gps-navigation-head-unit-support-mirror-link-dab-obdii-usb-tpms-3g-wifi-steering-wheel-control-1080p-video-s04155

This car radio will enable you to have a brand new in-car life since its operation system has been upgraded to the latest and stable Android 6.0 version and it has a powerful quad-core CPU processor.

Under the guidance of the worldwide real-time GPS navigation system, you are allowed to easily locate where you are and have the most suitable route option to arrive at your ideal destinations according to turn-by-turn directions and voice prompts. Besides, thanks to this unit’s dual zone function, you can freely enjoy your favorite music under GPS mode and the music will intelligently switch to GPS voice, which won’t have any negative influence on GPS function.

Besides, this unit comes with a very large 10.1 inch 1024*600 multi-touch screen to provide  you a wide field of viewing.

Wish you like this unit and good luck to you!