Home › Archive for Car DVD › Page 12

Car DVD

introduce car dvd products

How to Install a 2014 2015 KIA K5 OPTIMA Car Stereo with Bluetooth GPS Navigation System

Posted on by — 4 Comments ↓ 12,198 views
2014 2015 KIA K5 OPTIMA Car Stereo after installation

If you find your factory radio is too outdated to support a wide range of practical and entertainment features, it will be very wise of you to replace your factory radio with a new multifunctional car radio. With an ideal car radio installed in your car, you can have a more convenient and comfortable car interior environment as well as a more relaxing driving experience. The following is an installation guide for a 2014 2015 KIA K5 OPTIMA car radio. If you have the same or similar dashboard, you can refer to the following guide.

2014 2015 KIA K5 OPTIMA Car Stereo after installation
2014 2015 KIA K5 OPTIMA Car Stereo after installation

Precautions for this installation:

1. Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2. Please make sure that all fastened wires are isolated with electrical tape.

3. Please make sure the ignition is off to avoid short circuit.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2014 2015 KIA K5 OPTIMA car radio installation guide

1. Remove the panels shown as the pictures below, then set them aside.

Remove the panels shown as the pictures below, then set them aside
Remove the panels shown as the pictures below, then set them aside
1-1
1-1
1-2
1-2

2. Unscrew all the screws as the pictures below with a screwdriver.

Unscrew all the screws as the pictures below with a screwdriver
Unscrew all the screws as the pictures below with a screwdriver
2-1
2-1
2-2
2-2
2-3
2-3
2-4
2-4
2-5
2-5
2-6
2-6
2-7
2-7
2-8
2-8
2-9
2-9
2-10
2-10
2-11
2-11
2-12
2-12
2-13
2-13

3. Take out the air conditioner control.

Take out the air conditioner control
Take out the air conditioner control

4. Unscrew all the screws holding the air conditioner vent with a screwdriver.

Unscrew all the screws holding the air conditioner vent with a screwdriver
Unscrew all the screws holding the air conditioner vent with a screwdriver

5. Remove the air conditioner vent.

Remove the air conditioner vent
Remove the air conditioner vent

6. Unscrew four screws holding the original car radio with a screwdriver.

Unscrew four screws holding the original car radio with a screwdriver
Unscrew four screws holding the original car radio with a screwdriver
6-1
6-1
6-2
6-2

7. Gently take the original car radio out of the dash.

Gently take the original car radio out of the dash
Gently take the original car radio out of the dash

8. Disconnect all connectors at the back of the original car radio.

9. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

10. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

11. Connect the Seicane car radio to your original car radio ‘s plugs.

12. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

13.Put the new Seicane car radio into the dash.

14. Put everything into their original place. All the installation is done.

 

Now do you have a general understanding of the 2014 2015 KIA K5 OPTIMA car radio installation? If no, you can browse some professional websites. Or you can contact your dealer, communicate with someone experienced or turn to a professional for help. If you are afraid of making damage to either your car radio or your car, you can straightly go to a car radio upgrade center and ask a professional technician to help you install the new car radio. Any way, before installation, it is essential for you to select a suitable car radio from Seicane. Here I would like to share an amazing 2014 2015 KIA K5 OPTIMA car radio from Seicane with you. For more details, please click:

https://www.seicane.com/android-radio-gps-navigation-system-for-2014-2015-kia-k5-optima-with-hd-touch-screen-dvd-player-bluetooth-obd2-dvr-rearview-camera-tv-1080p-video-3g-wifi-steering-wheel-control-usb-sd-mirror-link-s168043

Loaded with the stable and latest Android 7.1 operation system, a powerful quad-core CPU processor and 2GB RAM, this all-in-one car radio can be regarded as one of the replacements for your factory radio.

Under the guidance of the turn-by-turn directions and voice prompts provided by the worldwide real-time GPS navigation system of high accuracy, you are able to easily and quickly know your current locations and find the most suitable way to get to your destinations. And with dual zone function, this unit makes it possible for you to listen to your favorite music under GPS mode, and the music will automatically switch to GPS voice.

Besides, through the Bluetooth connection between your Bluetooth-enabled mobile phone with this advanced car radio, you are able to dial, answer, reject and mute Bluetooth hands-free phone calls and listen to Bluetooth streaming music without taking hands off the steering wheel.

What’s more, you can turn on this unit’s function as a DVD player to play music, videos, TV programs, movies, etc to relax both yourself and your passengers. Therefore, you can gain greatest convenience and enjoyment.

Wish you like this unit and good luck to you!

How to Quickly Upgrade a 2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica Car Radio with DVD Player GPS Navigation System

Posted on by — No Comments ↓ 3,751 views
2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica Car Radio after installation

As for car owners, it will be very wonderful if they can enjoy the greatest convenience and entertainment in car as well as have a comfortable and relaxing in-car experience. If you are also desired to have both convenient and relaxing in-car life, you might as well replace your factory radio with a new aftermarket radio. The following is a 2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica car radio installation instruction which can be taken as a reference.

2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica Car Radio after installation
2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica Car Radio after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica car radio installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Grab at the bottoming plastic cover, push the bottoming box and release it.

Grab at the bottoming plastic cover, push the bottoming box and release it
Grab at the bottoming plastic cover, push the bottoming box and release it

3. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside
Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside
3-1
3-1

4. Unplug the connectors at the back of panel.

Unplug the connectors at the back of panel
Unplug the connectors at the back of panel

5. Remove four screws that fixed the radio on the dashboard.

Remove four screws that fixed the radio on the dashboard
Remove four screws that fixed the radio on the dashboard
5-1
5-1
5-2
5-2
5-3
5-3

6. Gently pull the factory radio out of the dash. Then unplug the connectors at the back of the factory radio.

Gently pull the factory radio out of the dash. Then unplug the connectors at the back of the factory radio
Gently pull the factory radio out of the dash. Then unplug the connectors at the back of the factory radio
6-1
6-1

7. Check all the accessories for the new Seicane head unit.

Check all the accessories for the new Seicane head unit
Check all the accessories for the new Seicane head unit

8. Connect the harnesses to the back of the new Seicane head unit.

Connect the harnesses to the back of the new Seicane head unit
Connect the harnesses to the back of the new Seicane head unit

9. Connect the Seicane head unit to your original head unit ‘s plugs.

10. Turn on the new Seicane head unit to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane head unit into the dash.

12. Put everything into their original place. All the installation is done.

 

Wish the above installation guide can be helpful for you. If you meet any difficulties, please don’t be worried. To overcome these difficulties, you can seek help from your dealer, someone experienced or a professional. If you still think it hard for you to install the new car radio by yourself, you can straightly arrange a technician to help you.

While for the selection of an ideal car radio for your car, if you have no ideas, you can check out the following link which is a remarkable 2006 2007 2008 2009 2010-2011 Chevy Chevrolet Epica  car radio from Seicane.

https://www.seicane.com/2006-2011-chevy-chevrolet-epica-android-aftermarket-radio-gps-touch-screen-navigation-system-dvd-player-bluetooth-mirror-link-obd2-dvr-rearview-camera-tv-usb-sd-3g-wifi-ipod-1080p-video-steering-wheel-control-s166235

This car radio runs on the latest Android 7.1 operation system and a powerful quad-core CPU processor to enhance its capabilities and performance. With this car radio installed in your car, you can get access to comprehensive functions and features in diverse, mainly including 3D GPS navigation system, FM/AM radio, Bluetooth hands-free phone calls, Bluetooth streaming music, DVD player, file management, USB or SD card connection, etc.

Thanks to turn-by-turn directions and voice prompts provided by GPS function, you can easily know your current locations and find the most suitable way to arrive at your destinations. And this unit’s dual zone function enables you to listen to your favorite music while navigating, which won’t have any negative influence on GPS function.

Wish you like this modern car radio. Good luck to you.

How to Replace a 2008 2009 2010 Jeep Commander Car Radio with Stereo Audio Speakers in a Quick Way

Posted on by — 4 Comments ↓ 6,467 views
2008 2009 2010 Jeep Commander Car Radio after installation

If you are an owner of a 2008 2009 2010 Jeep Commander and happen to plan to replace your factory radio with a brand new multifunctional car radio, you may need a correct installation instruction to help you. This article is mainly about a 2008 2009 2010 Jeep Commander car radio installation instruction, which may help you gain a general understanding of the old radio removal and the new car radio installation. Wish it is helpful for you to some extent.

2008 2009 2010 Jeep Commander Car Radio after installation
2008 2009 2010 Jeep Commander Car Radio after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2008 2009 2010 Jeep Commander car radio installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Remove the panel by prying the edges with a lever.

Remove the panel by prying the edges with a lever
Remove the panel by prying the edges with a lever

3. Unscrew four screws holding the original radio in place with a screwdriver.

Unscrew four screws holding the original radio in place with a screwdriver
Unscrew four screws holding the original radio in place with a screwdriver

4. Take the original radio out of the dash.

Take the original radio out of the dash
Take the original radio out of the dash

5. Disconnect the connectors at the back of the original radio.

Disconnect the connectors at the back of the original radio
Disconnect the connectors at the back of the original radio

6. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo
Check all the accessories for the new Seicane car stereo

7. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo
Connect the harnesses to the back of the new Seicane car stereo

8. Connect the Seicane car stereo to your original car radio’s plugs.

9. Turn on the new Seicane stereo to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane stereo into the dash.

11. Put everything into their original place.

 

Wish the above installation steps can be helpful for you to some extent. If you meet any problems and don’t know how to deal with, you can seek help from your dealer, someone experienced or a professional. Anyway, before installation, it is crucial to select an ideal car radio. If you don’t know which kind of car radio can fit your car well, you can check out the following link which is an excellent 2008 2009 2010 Jeep Commander car radio from Seicane.

https://www.seicane.com/android-radio-2008-2009-2010-jeep-commander-gps-navigation-bluetooth-usb-wifi-dvd-player-support-1080p-video-dvr-obd2-rearview-camera-steering-wheel-control-s6933

With this car radio installed in your car, you will able to embrace a smoother, easier and faster operation experience since this car radio runs on the advanced and stable Android 7.1 operation system and a powerful quad-core CPU processor to enhance and improve its capabilities and performance.

The worldwide real-time GPS navigation system is especially built in this car radio, so you don’t need to worry about getting lost any more even you have no good sense of directions. Through the turn-by-turn directions and voice prompts, you are able to easily know your current locations and find the most suitable way to reach your desired destinations.

Additionally, under Bluetooth technology, you are able to connect your Bluetooth-enabled mobile phone to this car radio so as to get access to Bluetooth hands-free phone calls for convenience and Bluetooth streaming music for enjoyment. Thus, you will gain a safer, more convenient and relaxing driving.

If you like this unit, just add it to your shopping cart right now. Good luck to you!

How to Remove a 2010 2011 2012 2013 Mazda 5/Premacy Car Radio to Install a Touch Screen Radio Stereo Navigation System

Posted on by — 2 Comments ↓ 6,530 views
2010 2011 2012 2013 Mazda 5 Premacy Car Radio after installation

There is no doubt that to have both a comfortable car interior environment and a relaxing driving experience is what most car owners are pursuing at present. And to achieve that goal, it is wise of you to think about replacing your factory radio with a new aftermarket car radio. The following is a 2010 2011 2012 2013 Mazda 5/Premacy car radio installation guide. If you have the same or similar dashboard, you can refer to the following guide and take it as a reference.

2010 2011 2012 2013 Mazda 5 Premacy Car Radio after installation
2010 2011 2012 2013 Mazda 5 Premacy Car Radio after installation

Here are some tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and www.seicane.com make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd- 400

2010 2011 2012 2013 Mazda 5/Premacy car radio installation guide

1. Unclip and remove the cup holder panel in the center console.

Unclip and remove the cup holder panel in the center console
Unclip and remove the cup holder panel in the center console
1-1
1-1

2. Unclip and remove the small pocket panel on the back of the center console behind shifter.

Unclip and remove the small pocket panel on the back of the center console behind shifter
Unclip and remove the small pocket panel on the back of the center console behind shifter
2-1
2-1
2-2
2-2

3. Remove two 8mm bolts under the cup holder panel holding the back half of the center console to the front half.

Remove two 8mm bolts under the cup holder panel holding the back half of the center console to the front half
Remove two 8mm bolts under the cup holder panel holding the back half of the center console to the front half

4. Unscrew the shift knob and remove it carefully.

Unscrew the shift knob and remove it carefully
Unscrew the shift knob and remove it carefully

5. Unclip and remove the shifter trim panel.

Unclip and remove the shifter trim panel
Unclip and remove the shifter trim panel

6. Slide both seats forwards and remove two Phillips screws on each side of the center console under the screw covers.

Slide both seats forwards and remove two Phillips screws on each side of the center console under the screw covers
Slide both seats forwards and remove two Phillips screws on each side of the center console under the screw covers
6-1
6-1

7. Unclip and pull back the panels at the lower front sides of the center console.

Unclip and pull back the panels at the lower front sides of the center console
Unclip and pull back the panels at the lower front sides of the center console

8. Remove two Phillips screws from both sides(total of four) of the front lower half of the center console.

Remove two Phillips screws from both sides(total of four) of the front lower half of the center console
Remove two Phillips screws from both sides(total of four) of the front lower half of the center console
8-1
8-1

9. Unclip and remove the vent panel including the hazard switch above the factory radio. Then it will be much easier for you to get access to the screws. And remove the two screws.

Unclip and remove the vent panel including the hazard switch above the factory radio. Then it will be much easier for you to get access to the screws. And remove the two screws
Unclip and remove the vent panel including the hazard switch above the factory radio. Then it will be much easier for you to get access to the screws. And remove the two screws
9-1
9-1
9-2
9-2

10. Remove two screws from behind the shifter trim.

Remove two screws from behind the shifter trim
Remove two screws from behind the shifter trim
10-1
10-1

11. Pull center console forward so as to gain access to two screws under the climate controls. And then remove these two screws.

Pull center console forward so as to gain access to two screws under the climate controls. And then remove these two screws
Pull center console forward so as to gain access to two screws under the climate controls. And then remove these two screws
11-1
11-1

12. Unclip harness and pull rear center console backwards.

Unclip harness and pull rear center console backwards
Unclip harness and pull rear center console backwards

13. Press in shifter to release trigger and pull shifter down, make sure to have a brake on.

Press in shifter to release trigger and pull shifter down, make sure to have a brake on
Press in shifter to release trigger and pull shifter down, make sure to have a brake on

14. Use a pry tool to release climate controls.

Use a pry tool to release climate controls
Use a pry tool to release climate controls

15. Remove one screw and one 10mm bolt.

Remove one screw and one 10mm bolt
Remove one screw and one 10mm bolt

16. Pull factory radio out, release clips and unplug radio connectors.

Pull factory radio out, release clips and unplug radio connectors
Pull factory radio out, release clips and unplug radio connectors

17. Check all the accessories for the new Seicane car radio.

18. Connect the harnesses to the back of the new Seicane car radio.

19. Connect the Seicane car radio to your original car radio ‘s plugs.

20. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

21. Put the new Seicane radio into the dash.

22. Put everything into their original place. All the installation is done.

 

Now do you have a general understanding of 2010 2011 2012 2013 Mazda 5/Premacy car radio installation? If not, please feel free to seek advice from your dealer, communicate with someone experienced or turn to a professional for help. Or you can directly arrange a professional technician to help you install the new car radio. Anyway, before installation, please do select an ideal car radio. If you have no ideas, you can refer to the following link which is an amazing 2010 2011 2012 2013 Mazda 5/Premacy car radio from Seicane.

https://www.seicane.com/hd-touchscreen-android-gps-navigation-car-radio-dvd-player-for-2010-2013-mazda-5-premacy-with-bluetooth-canbus-usb-wifi-obd2-dvr-aux-mirror-link-steering-wheel-control-s18m015

This car radio comes with a wide range of practical and entertainment features to meet your different needs in car. So it can be regarded as one of the best choices to replace your factory radio.

After you get this car radio installed in your car, you can make full use of its built-in GPS navigation system of high accuracy. Through the text-to-speech guidance, you can easily locate where you are and accurately navigate to any locations you would like to go to.

Besides, as long as you connect your Bluetooth-enabled mobile phone to this unit through Bluetooth connection, you can dial, answer, reject or mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music without taking your hands off the steering wheel.

If you like this unit, just add it to your shopping cart. Good luck!

How to Effectively Replace a 2015 2016 2017 JEEP Wrangler Car Radio with DVD Player Bluetooth GPS Navigation System

Posted on by — No Comments ↓ 5,743 views
2015 2016 2017 JEEP Wrangler Car Radio after installation

Would you like to enjoy more up-to-date features brought by an ideal car radio in your car while you are driving? If yes, why not think about replacing your factory radio with a new multifunctional car radio. If you have a 2015 2016 2017 JEEP Wrangler and plan to install a new aftermarket car radio so as to embrace a brand new driving experience, then you can take the following related installation guide as a reference. Wish you can get some help from the guide.

2015 2016 2017 JEEP Wrangler Car Radio after installation
2015 2016 2017 JEEP Wrangler Car Radio after installation

Tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2015 2016 2017 JEEP Wrangler car radio installation instruction

1. Get the window control out of the original place, so that you can get access to the screw that is behind it.

Get the window control out of the original place, so that you can get access to the screw that is behind it
Get the window control out of the original place, so that you can get access to the screw that is behind it

2. Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control.

Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control
Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control
2-1
2-1

3. You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out.

You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out
You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out
3-1
3-1

4. There is a clip and you need to push it down and make it come right off, after that, put this window control to the side.

There is a clip and you need to push it down and make it come right off, after that, put this window control to the side
There is a clip and you need to push it down and make it come right off, after that, put this window control to the side
4-1
4-1
4-2
4-2
4-3
4-3

5. Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray.

Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray
Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray
5-1
5-1
5-2
5-2

6. Next you are going to pull away the trim under the steering wheel.

Next you are going to pull away the trim under the steering wheel
Next you are going to pull away the trim under the steering wheel
6-1
6-1

7. With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set.

With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set
With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set

8. Firmly pull the dash and it should be clipped out.

Firmly pull the dash and it should be clipped out
Firmly pull the dash and it should be clipped out
8-1
8-1

9. With the dash removed, you now can have access to the four bolts that are holding the original car radio.

With the dash removed, you now can have access to the four bolts that are holding the original car radio
With the dash removed, you now can have access to the four bolts that are holding the original car radio

10. Remove these four bolts with the seven millimeter screwdriver.

Remove these four bolts with the seven millimeter screwdriver
Remove these four bolts with the seven millimeter screwdriver

11. With all the bolts removed, the original car radio should simply slide out from the original place.

With all the bolts removed, the original car radio should simply slide out from the original place
With all the bolts removed, the original car radio should simply slide out from the original place
11-1
11-1

12. Disconnect the factory connectors and wires at the back of the original car radio.

Disconnect the factory connectors and wires at the back of the original car radio
Disconnect the factory connectors and wires at the back of the original car radio

13. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

14. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

15. Connect the Seicane car radio to your original radio’s plugs.

16. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

17. Put the new Seicane car radio into the dash.

18. Put everything into their original place. All the installation is done.

 

Above is the whole removal and installation process for a 2015 2016 2017 JEEP Wrangler. If you have any doubts, please don’t hesitate to seek help from your dealer, someone experienced or a professional. Besides, it is essential for you to pick an ideal car radio for your car. If you have no ideas, here I would like to recommend a remarkable 2015 2016 2017 JEEP Wrangler car radio from Seicane to you. For more details, please click:

https://www.seicane.com/en/android-touchscreen-radio-for-2015-2017-jeep-wrangler-bluetooth-music-gps-navigation-head-unit-support-mirror-link-dab-obdii-usb-tpms-3g-wifi-steering-wheel-control-1080p-video-s04155

This car radio will enable you to have a brand new in-car life since its operation system has been upgraded to the latest and stable Android 6.0 version and it has a powerful quad-core CPU processor.

Under the guidance of the worldwide real-time GPS navigation system, you are allowed to easily locate where you are and have the most suitable route option to arrive at your ideal destinations according to turn-by-turn directions and voice prompts. Besides, thanks to this unit’s dual zone function, you can freely enjoy your favorite music under GPS mode and the music will intelligently switch to GPS voice, which won’t have any negative influence on GPS function.

Besides, this unit comes with a very large 10.1 inch 1024*600 multi-touch screen to provide  you a wide field of viewing.

Wish you like this unit and good luck to you!

The Quick Tutorial on a 2011 2012 KIA K2 RIO Car Radio Installation with Bluetooth GPS Navigation System

Posted on by — No Comments ↓ 2,624 views
2011 2012 KIA K2 RIO Car Radio after installation

To enrich your in-car life or take your in-car life up a level, you can easily replace your factory radio with a new aftermarket car radio. There is no doubt that an ideal car radio can make you enjoy more convenience and enjoyment. If you have some related installation, you can follow the related installation guide to deal with the installation. The following is a 2011 2012 KIA K2 RIO car radio installation instruction which can be taken as your reference.

2011 2012 KIA K2 RIO Car Radio after installation
2011 2012 KIA K2 RIO Car Radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2011 2012 KIA K2 RIO car radio installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Use a plastic removal tool to release the top panel.

Use a plastic removal tool to release the top panel
Use a plastic removal tool to release the top panel

3. Pry the trim panel of the radio with a plastic knife and remove it.

Pry the trim panel of the radio with a plastic knife and remove it
Pry the trim panel of the radio with a plastic knife and remove it
3-1
3-1

4. Unscrew the screws that are holding the radio on the dashboard.

Unscrew the screws that are holding the radio on the dashboard
Unscrew the screws that are holding the radio on the dashboard

5. Take out the radio gently.

Take out the radio gently
Take out the radio gently

6. Unplug the connectors and cables at the back of the radio.

Unplug the connectors and cables at the back of the radio
Unplug the connectors and cables at the back of the radio

7. Check all the accessories for the new Seicane car radio.

8. Connect the harnesses to the back of the new Seicane car radio.

9. Connect the Seicane car radio to your original radio’s plugs.

10. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

11. Put the new Seicane car radio into the dash.

12. Put everything into their original place. All the installation is done.

 

Wish you can learn something useful from the above installation instruction. If you meet any difficulties you don’t know how to overcome, you might as well seek help from your dealer, someone experienced or a professional. Or you can directly arrange a professional technician to help you install the new car radio. Additionally, to help you select a suitable car radio, here I would like to share a marvelous 2011 2012 KIA K2 RIO car radio from Seicane with you. Here comes the related link, please click:

https://www.seicane.com/android-touchscreen-2011-2012-kia-k2-rio-radio-gps-navigation-system-with-dvr-bluetooth-steering-wheel-control-backup-camera-mirror-link-obd2-digital-tv-s18k212

This remarkable car radio with a large 9 inch screen is loaded with the intelligent Android 7.1 operation system, a quad-core 1.6 GHz RK-PX3 CPU processor and 2GB RAM to enable you to enjoy its higher capabilities and performance.

Under the guidance of the turn-by-turn directions and voice prompts offered by the built-in precise GPS navigation system, it will become much easier for you to know your current locations and navigate to any locations you would like to go to. And this unit’s dual zone function enables you to listen to your favorite music while navigating, which won’t have any negative influence on GPS function.

Through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, without taking your hands off the steering wheel, you are able to dial, answer, reject and mute hands-free calls as well as listen to beautiful music streaming from your phone. By doing so, you will gain a lot of convenience and enjoyment.

Wish you enjoy your relaxing trip accompanied by this car radio. Good luck!

Skills to Replace a 2012 2013 Toyota CAMRY GPS DVD Bluetooth Car Radio

Posted on by — No Comments ↓ 2,928 views
2012 2013 Toyota CAMRY GPS DVD Bluetooth Car Radio after installation

As the technology greatly improves, nowadays a car radio is usually compatible with more and more modern features. If you think your factory radio is out of date, it is suggested that you replace it with a new aftermarket car radio. This article is mainly about how to remove the factory radio and install the new car radio for 2012 2013 Toyota CAMRY. If you happen to own the same or similar dashboard, you can refer to it to deal with the installation.

2012 2013 Toyota CAMRY GPS DVD Bluetooth Car Radio after installation
2012 2013 Toyota CAMRY GPS DVD Bluetooth Car Radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts (Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7.For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

2012 2013 Toyota CAMRY car radio installation instruction

1. Remove the lower dashboard trim panels and the upper air conditioning vents.

Remove the lower dashboard trim panels and the upper air conditioning vents
Remove the lower dashboard trim panels and the upper air conditioning vents
1-1
1-1
1-2
1-2

2. Gently pry the upper dashboard housing from the radio’s trim bazel using either an automotive trim tool or your hands.

Gently pry the upper dashboard housing from the radio's trim bazel using either an automotive trim tool or your hands
Gently pry the upper dashboard housing from the radio’s trim bazel using either an automotive trim tool or your hands

3. After the upper dashboard housing has been disconnected, remove the two upper &two lower radio mounting screws from the dashboard.

After the upper dashboard housing has been disconnected, remove the two upper &two lower radio mounting screws from the dashboard
After the upper dashboard housing has been disconnected, remove the two upper &two lower radio mounting screws from the dashboard
3-1
3-1
3-2
3-2
3-3
3-3

4. Once the four radio mounting screws have been removed, gently lift the radio from the dashboard in order to gain access to the factory wiring harnesses on the backside.

Once the four radio mounting screws have been removed, gently lift the radio from the dashboard in order to gain access to the factory wiring harnesses on the backside
Once the four radio mounting screws have been removed, gently lift the radio from the dashboard in order to gain access to the factory wiring harnesses on the backside
4-1
4-1

5. Disconnect the connectors at the back of the radio.

6. Check all the accessories for the new Seicane car radio.

7. Connect the harnesses to the back of the new Seicane car radio.

8. Connect the Seicane car radio to your original radio’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

Before installation, please confirm that you understand every detailed step. If you have any doubts, please don’t hesitate to seek help from your dealer, someone experienced or a professional. Or you can directly arrange a professional to help you install the new car radio. Anyway, first of all, it is essential for you to select an ideal car radio, here I would like to recommend an amazing 2012 2013 Toyota CAMRY car radio from Seicane to you.

https://www.seicane.com/full-touchscreen-2012-2013-toyota-camry-android-gps-navigation-system-with-radio-rearview-camera-4g-wifi-bluetooth-mirror-link-obd2-dvr-steering-wheel-control-s18t252

This car radio comes with a super large 10.2 inch HD 1024 x 600 multi-touch screen. Based on the most advanced Android 7.1 operation system and a high-quality quad-core 1.6GHz RK PX3 processor, this car radio can greatly facilitate the operation so as to provide its users with a brand new and wonderful operation experience.

Under the guidance of the turn-by-turn directions and voice prompts offered by the worldwide real-time GPS navigation system of high accuracy, you can easily know your current locations and have the optimal route option to reach your desired destinations. And you can also listen to radio, USB or SD card music playback while navigating thanks to this unit’s dual zone function.

Wish you like this unit and good luck to you!

How to Upgrade a 2011 2012 2013 Kia k5 Car Stereo with Radio CD Player in a Fast Way

Posted on by — No Comments ↓ 2,789 views
2011 2012 2013 Kia k5 Car Stereo after installation

If you are a car owner of a 2011 2012 2013 Kia k5, then you can have a look at the following image, which is a 2011 2012 2013 Kia k5 car radio from Seicane after installation. It looks very amazing, isn’t it? If you are fed up with your factory radio and also want to replace your factory radio, you can carefully refer to the following 2011 2012 2013 Kia k5 car radio installation guide.

2011 2012 2013 Kia k5 Car Stereo after installation
2011 2012 2013 Kia k5 Car Stereo after installation

Please pay attention to the following notice before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd- 400

2011 2012 2013 Kia k5 car radio installation guide

1. There is a panel shown in the picture, use a plastic knife to pry it.

There is a panel shown in the picture, use a plastic knife to pry it
There is a panel shown in the picture, use a plastic knife to pry it
1-1
1-1

2. Remove four screws that fixed the panel near the AC control.

Remove four screws that fixed the panel near the AC control
Remove four screws that fixed the panel near the AC control
2-1
2-1
2-2
2-2

3. Use the plastic removal tool to remove the decorated panel around the radio.

Use the plastic removal tool to remove the decorated panel around the radio
Use the plastic removal tool to remove the decorated panel around the radio
3-1
3-1

4. Remove screws that fixed the AC control so as to remove the AC control.

Remove screws that fixed the AC control so as to remove the AC control
Remove screws that fixed the AC control so as to remove the AC control
4-1
4-1

5. Unscrew screws to release the panel on the left side of the radio and the radio trim panel.

Unscrew screws to release the panel on the left side of the radio and the radio trim panel
Unscrew screws to release the panel on the left side of the radio and the radio trim panel
5-1
5-1
5-2
5-2
5-3
5-3

6. Remove four screws that are holding the radio on the dashboard.

7. Gently take out the original car radio.

8. Disconnect the connectors and cables at the back of the radio.

9. Check all the accessories for the new Seicane car radio.

10. Connect the harnesses to the back of the new Seicane car radio.

11. Connect the Seicane car radio to your original radio’s plugs.

12. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

13. Put the new Seicane car radio into the dash.

14. Put everything into their original place. All the installation is done.

 

Before installation, please make clear every detailed step. If you encounter any difficulties you cannot overcome independently, please feel free to seek help from your dealer, someone experienced or a professional. Or you can directly ask a professional technician to help you install the new car radio. Anyway, before installation, you should pick an ideal car radio. If you don’t have any ideas, you can refer to the link below which is an amazing 2011 2012 2013 Kia k5 car radio from Seicane.

https://www.seicane.com/2011-2012-2013-kia-k5-android-radio-gps-navigation-system-with-hd-touchscreen-bluetooth-steering-wheel-control-digital-tv-mirror-link-backup-camera-tpms-s18k215

This car radio runs much smoother and faster since it is running on the most advanced and stable Android 7.1 operation system ,a 1.6GHz RK PX3 quad-core processor and 2 GB RAM.

With the assistance of the worldwide real-time GPS navigation system, you will be accurately provide with your current locations and the optimal routes and led to any locations you would like to go to according to turn-by-turn direction and voice prompts. Thanks to this unit’s dual zone function, you will be able to listen to your favorite music while navigating.

Besides, with a built-in digital FM/AM radio tuner, this car A/V system features searching radio channels automatically, manually and storing them in the process.

What are you waiting for? If you like this unit, just add it to your shopping cart right now!

Easy Steps to Replace a 2012 CITROEN C4 Bluetooth GPS DVD Touch Screen Car Radio

Posted on by — No Comments ↓ 4,511 views
2012 CITROEN C4 Bluetooth GPS DVD Touch Screen Car Radio after installation

To embrace a more comfortable in-car environment and driving experience, one of the straightforward ways is to replace your factory radio with a new aftermarket car radio. And to reduce some budget on the replacement of the car radio, you can try to install the new car radio on your own. We write this article to mainly introduce a 2012 CITROEN C4 car radio installation guide from Seicane. If you have the same or similar dashboard, you can take this guide as a reference.

2012 CITROEN C4 Bluetooth GPS DVD Touch Screen Car Radio after installation
2012 CITROEN C4 Bluetooth GPS DVD Touch Screen Car Radio after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2012 CITROEN C4 car radio installation guide

1. The original car radio.

The original car radio
The original car radio

2. Use a plastic knife to pry the trim panel and remove it.

Use a plastic knife to pry the trim panel and remove it
Use a plastic knife to pry the trim panel and remove it
2-1
2-1
2-2
2-2

3. Remove screws that are holding the radio.

Remove screws that are holding the radio
Remove screws that are holding the radio

4. Take out the original car radio.

Take out the original car radio
Take out the original car radio

5. Disconnect the connectors and cables at the back of the radio.

Disconnect the connectors and cables at the back of the radio
Disconnect the connectors and cables at the back of the radio

6. Check all the accessories for the new Seicane car radio.

7. Connect the harnesses to the back of the new Seicane car radio.

8. Connect the Seicane car radio to your original stereo’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

Above are all steps about the installation of a 2012 CITROEN C4 car radio. Wish you can learn some skills from them. To overcome some difficulties you meet in the removal and installation process, you can browse some professional websites or seek help from your dealer, someone experienced or a professional. But if you haven’t selected an ideal car radio yet, you may check out the following link which is a wonderful 2012 CITROEN C4 car radio from Seicane.

https://www.seicane.com/2012-citroen-c4-dvd-player-radio-android-navigation-system-mirror-link-gps-hd-touch-screen-obd2-dvr-tv-1080p-video-3g-wifi-steering-wheel-control-bluetooth-usb-sd-backup-camera-s168064

This great 2012 CITROEN C4 car radio can be regarded as your perfect road companion since it comes with higher configuration and better performance.

This unit’s built-in worldwide real-time GPS navigation system allows you to easily know your current locations and have the optimal route options to arrive at any locations you would like to go to according to turn-by-turn directions and voice prompts.

Thanks to this unit’s additional entertainment features, you can utilize its function as a multimedia player to play music, videos, TV programs, movies, etc, which may relax both yourself and your passengers.

Wish you like this unit and good luck to you!

The Most Effective Way to Upgrade a 2009 2010 2011 2012 2013 Subaru outback GPS Car Radio with Bluetooth Speakers Navigation DVD Player

Posted on by — 4 Comments ↓ 9,207 views
2009 2010 2011 2012 2013 Subaru outback GPS Car Radio after installation

First of all, please look at the following image. It is a 2009 2010 2011 2012 2013 Subaru outback car radio from Seicane after installation. It looks very awesome, isn’t it? If you have the same or similar dashboard and would like to upgrade your factory radio, you can refer to the following installation guide to help with the new car radio installation.

2009 2010 2011 2012 2013 Subaru outback GPS Car Radio after installation
2009 2010 2011 2012 2013 Subaru outback GPS Car Radio after installation

Here are some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriverbefore the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s therecommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

2009 2010 2011 2012 2013 Subaru outback car radio installation guide

1. The original car radio.

The original car radio
The original car radio

2. Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside.

Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside
Remove the original panel with a plastic knife, pry gently along the gap and pick up the panel, then remove it and then set it aside
2-1
2-1
2-2
2-2

3. Remove six screws that fixed the radio on the dashboard.

Remove six screws that fixed the radio on the dashboard
Remove six screws that fixed the radio on the dashboard
3-1
3-1
3-2
3-2
3-3
3-3

4. Gently pull the factory radio out of the dash.

Gently pull the factory radio out of the dash
Gently pull the factory radio out of the dash

5. Then unplug the connectors at the back of the factory radio.

Then unplug the connectors at the back of the factory radio
Then unplug the connectors at the back of the factory radio

6. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

7. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

8. Connect the Seicane car radio to your original radio’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

That’s the whole removal and installation process for a 2009 2010 2011 2012 2013 Subaru outback car radio. If you cannot fully understand, please feel free to seek help from your dealer,, someone experienced or a professional. Besides, if you still think it hard for you to finish the whole installation process, you can directly arrange a professional to help you install the new car radio.

To help you select an ideal car radio, I would like to recommend a fabulous 2009 2010 2011 2012 2013 Subaru outback car radio from Seicane to you. Here comes the link, please click:

https://www.seicane.com/2009-2013-subaru-outback-android-radio-gps-navigation-system-with-bluetooth-dvd-player-with-hd-touch-screen-obd2-dvr-rearview-camera-tv-1080p-video-3g-wifi-steering-wheel-control-usb-sd-mirror-link-s167069

Even you are driving around an unfamiliar city, you can depend on the built-in 3D GPS navigation system. With its help, you can plan the most suitable route to get to your destinations without mistakes through text-to-speech guidance. And this unit’s dual zone function makes it possible for you to enjoy your favorite music while navigating.

Besides, to guarantee your driving safety, the Bluetooth module is built in to make it possible for you to dial, receive or reject hands-free phone calls as well as enjoy streaming music from your phone music playlists without keeping your hands off the steering wheel.

What are you waiting for? Just add this unit to your shopping cart right now!