When considering enhancing your car’s capabilities, as far as I am concerned, the easiest an most popular way you can adopt is to upgrade your factory radio. An ideal car radio can only improve your car interior environment but also bring a lot of convenience and enjoyment for your. The following is a 2016 Jeep Renegade car radio installation guide from Seicane. If you also have the same or similar dashboard, then you can read the following guide to help install your new car radio in your car.
2016 Jeep Renegade Bluetooth GPS Car Radio after installation
Before and during installation, you should notice:
1. Before connecting, please make sure the ignition is off to avoid short circuit.
2. Ensure connect the yellow and red power cable at last.
3. Ensure that all loose wires are isolated with electrical tape
4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
5. Ensure that all ground is connected to the same place.
6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.
1. Start by removing the car radio trim panel using a flat pry tool.
Start by removing the car radio trim panel using a flat pry tool1-1
2. Use a screwdriver to remove screws that are holding the radio on the dashboard.
Use a screwdriver to remove screws that are holding the radio on the dashboard
3. Gently pull the original radio out from the dash.
Gently pull the original radio out from the dash
4. Disconnect all the connectors and cables at the back of the radio.
Disconnect all the connectors and cables at the back of the radio
5. Check all the accessories for the new Seicane car radio.
Check all the accessories for the new Seicane car radio
6. Connect the harnesses to the back of the new Seicane car radio.
Connect the harnesses to the back of the new Seicane car radio
7. Connect the Seicane car radio to your original radio’s plugs.
8. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
9. Put the new Seicane car radio into the dash.
10. Put everything into their original place. All the installation is done.
After reading the above installation guide, if you have any doubts about the wiring, you can contact your dealer for seeking a wiring diagram. Or you can turn to a professional for help. If you still think it hard for you to finish the whole upgrade process by yourself, you’d better directly go to a car radio upgrade center and ask a professional to help you install the new car radio.
Since an ideal car radio matters a lot in installation, if you don’t know how to select a suitable car radio for your beloved car, I’d like to share an amazing 2016 Jeep Renegade car radio from Seicane with you. For more details, please click:
This car radio can be regarded as one of your best choices to replace your factory radio. Loaded with the advanced and stable Android 6.0 operation system and equipped with a powerful quad-core CPU processor, this car radio enables you to embrace much smoother and faster operation experience than ever before.
Under the guidance of turn-by-turn direction and voice prompts provided by the high-end 3D GPS navigation system, you will have difficulty in knowing your current locations and navigating to your desired destinations. Additionally, while navigating, you can freely listen to music thanks to this unit’s dual zone function. And the music will automatically switch to GPS voice.
While for entertainment features, you can watch fantastic videos, TV programs and movies, etc through this large 9 inch HD 1024*600 multi-touch screen. It will show you wonderful display effect and enable you to have a good view of the road ahead.
If you like this car radio, just remember to add it to your shopping cart. Good luck to you!
There is no denying that an ideal car radio can play a significant role in your driving as it controls the entertainment system of a car. However, you may find that your factory radio may not be compatible enough to support a lot of features that will meet most of your needs in car. In that case, it is wise of you to upgrade your factory radio with an intelligent car radio which comes with a lot of comprehensive features. The following is a 2013 2014 Toyota Vios car radio installation guide from Seicane which can be taken as your reference.
2013 2014 Toyota Vios Bluetooth GPS Car Radio Stereo after installation
Tips about the installation:
1.Please disconnect the power before the installation.
2.Please prepare a lever and a screwdriver before the removal and the installation.
3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.
2013 2014 Toyota Vios car radio installation guide
1. The original car radio.
The original car radio
2. Remove the panel with your hands,please use a plastic removal tool if necessary.
Remove the panel with your hands,please use a plastic removal tool if necessary2-1
3. Disconnect the connector at the back of the air vent.
Disconnect the connector at the back of the air vent
4. Use a screwdriver to remove four screws that are holding the original car radio.
Use a screwdriver to remove four screws that are holding the original car radio
5. Gently take out the original car radio from thedashboard.
6. Unplug the connectors and cables at the back of the original car radio.
Unplug the connectors and cables at the back of the original car radio
7. Check all the accessories for the new Seicane car radio.
8. Connect the harnesses to the back of the new Seicane car radio.
9. Connect the Seicane car radio to your original car radio’s plugs.
10. Put the new Seicane car radio into the dash.
11. Turn on the new Seicane car radio and have a comprehensive check if it works well.
12. Install 4 screws back to their original position.
13. Install the trim panel back to its original place.
Above steps are all about how to remove the factory radio and install the new car radio in a 2013 2014 Toyota Vios. If you cannot fully understand these steps, you can consult your dealer or ask for a professional for help. Or you can directly go to a car radio upgrade center to have the new car radio installed by a professional technician. Besides, to help you select an ideal car radio, here I would like to recommend a marvelous 2013 2014 Toyota Vios car radio from Seicane to you. Here comes the related link, please click:
This car radio is running on the stable Android 6.0 operation system and a quad-core CPU processor, so with it installed in your car, you can enjoy its stable and smooth performance.
After you install this car radio in your car, you can get access to a wide range of comprehensive features, including GPS navigation, FM/AM radio tuner, Bluetooth hands-free calls, Bluetooth streaming music, AUX, steering wheel control, USB & SD card connections, etc.
Under the guidance of turn-by-turn directions and voice prompts provided by the high-end 3D GPS navigation system, you can find the right way to reach any locations you would like to go to. And this unit’s dual zone function enables you to listen to your favorite music while navigating.
Besides, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, Bluetooth hands-free calls and Bluetooth streaming music are both available for you to gain great convenience and enjoyment.
If you are not satisfied with your factory radio since it cannot support many modern features to upgrade your in-car life, it is suggested that you should replace your factory radio with a new aftermarket car radio. After picking an ideal car radio, whether you plan to install the new car radio by yourself or ask a professional technician to help you install the new car radio, you can find a detailed installation instruction to help you. Here I would like to introduce a 2006 2007 2008 2009 2010 Toyota Camry car radio installation instruction from Seicane to you. If you have the same or similar dashboard, you might as well take it as a reference.
2006 2007 2008 2009 2010 Toyota Camry GPS Bluetooth Car Radio after installation
Tips about the installation:
1.Please disconnect the power before the installation.
2.Please prepare a lever and a screwdriver before the removal and the installation.
3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.
2006 2007 2008 2009 2010 Toyota Camry car radio installation instruction
1. The original car radio.
The original car radio
2. Make sure that your car engages the parking brake.
3. Rotate the shift lever knob counterclockwise.
Rotate the shift lever knob counterclockwise
4. Grab and remove the two side panels.
Grab and remove the two side panels
5. Remove the panel around the shift lever and then unplug the connector at the backside.
Remove the panel around the shift lever and then unplug the connector at the backside5-15-2
6. Remove the plastic part shown in the following picture and then unplug the connector at the backside.
Remove the plastic part shown in the following picture and then unplug the connector at the backside
7. Unscrew two screws that are holding the pocket.
Unscrew two screws that are holding the pocket7-1
8. Take out the pocket and disconnect the connectors at the back of it.
Take out the pocket and disconnect the connectors at the back of it8-18-2
9. Use a removal tool to pry the air vent and then remove it.
Use a removal tool to pry the air vent and then remove it9-1
10. There are two top screws and two bottom screws fix the radio on the dashboard. Remove them with a screwdriver.
There are two top screws and two bottom screws fix the radio on the dashboard. Remove them with a screwdriver10-1
11. Take out the original car radio gently.
Take out the original car radio gently
12. Disconnect the connectors and cables at the back of the radio.
13. Check all the accessories for the new Seicane car radio.
Check all the accessories for the new Seicane car radio
14. Connect the harnesses to the back of the new Seicane car radio.
Connect the harnesses to the back of the new Seicane car radio
15. Connect the Seicane car radio to your original stereo’s plugs.
16. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
17. Put the new Seicane car radio into the dash.
18. Put everything into their original place.
Now do you have a general understanding of the whole installation process about 2006 2007 2008 2009 2010 Toyota Camry car radio? If not, please feel free to contact your dealer, communicate with someone experienced or turn to a professional for help. Or you can directly arrange a technician to help install the new car radio.
Anyway, it is essential for you to select an ideal car radio for your beloved car, if you have no ideas, you might as well check out the following link which is a remarkable 2006 2007 2008 2009 2010 Toyota Camry car radio from Seicane.
This car radio is loaded with the stable Android 6.0 operation system and a quad-core CPU processor to enhance its capabilities and performance.
With this car radio installed in your car, you are able to get access to a wide range of practical and entertainment features to meet your needs. Here I would like to introduce its GPS function and Bluetooth function.
Thanks to the built-in 3D GPS navigation system of high accuracy, you can quickly locate where you are and accurately navigate to your destinations through turn-by-turn direction and voice prompts. And with dual zone function, this car radio enables you to listen to music which is played behind the scene under GPS mode, which won’t have any negative influence on GPS function.
Besides, under the wireless Bluetooth technology, you are able to connect your Bluetooth-enabled mobile phone to this car radio so as to dial, answer, reject and mute hands-free calls as well as listen to Bluetooth streaming music from your phone playlists without taking your hands off the steering wheel.
When traveling around an unfamiliar city, you can turn on your car radio with GPS function to navigate you to your desired destinations and make full use of its entertainment features to relax both yourself and your passengers. However, if your original car radio is not up-to-date enough to be compatible with so many advanced features, it is suggested that you should replace your factory radio with a new aftermarket car radio. Here I would like to share an easy installation instruction on a 2007 2008 2009 2010 2011-2013Honda Fit car radio from Seicane with you. If you have the same or similar dashboard, you can take it as reference.
2007 2008 2009 2010 2011-2013 Honda Fit Car Radio after installation
Before and during installation, you should notice:
1.Before connecting, please make sure the ignition is off to avoid short circuit.
2.Ensure connect the yellow and red power cable at last.
3.Ensure that all loose wires are isolated with electrical tape
4.Ensure don’t tangle the wire when tighten the moving parts (Such as seat rails).
5.Ensure that all ground is connected to the same place.
6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.
2007 2008 2009 2010 2011-2013 Honda Fit car radio installation instruction
1. Open the glove box at first.
Open the glove box at first
2. Remove the four screws of gloves box as these pictures show.
Remove the four screws of gloves box as these pictures show2-22-32-4
3. Unscrew the two bolts under the radio.
Unscrew the two bolts under the radio3-2
4. Take out the original car radio.
Take out the original car radio
5. Remove the original car radio.
Remove the original car radio
6. Disconnect all connectors at the back of the original car radio.
Disconnect all connectors at the back of the original car radio
7. Remove screws of air condition as these pictures show.
Remove screws of air condition as these pictures show7-27-37-47-5
8. Pull out the air outlet of air condition.
Pull out the air outlet of air condition
9. Remove the hazard warning switch light.
Remove the hazard warning switch light
10. Install the air outlet with the unit.
11. Check all the accessories for the new Seicane car radio.
12. Connect the harnesses to the back of the new Seicane car radio.
13. Connect the Seicane car radio to your original car radio’s plugs.
14. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
15. Put the new Seicane radio into the dash.
16. Put everything into their original place. All the installation is done.
That’s the whole process about the removal and installation of a 2007 2008 2009 2010 2011-2013Honda Fit car radio. If you have any questions, please fee free to browse some professional websites, contact your dealer or turn to a professional for help. Or you can directly ask a technician to help you install the new car radio. Anyway, it is necessary for you to select an ideal car radio first of all. If you don’t know how to pick a car radio that can work well with your car, here I’d like to recommend an excellent 2007 2008 2009 2010 2011-2013Honda Fit car radio from Seicane to you. For more details, please click:
This car radio with a large 10.1 inch multi-touch screen is running on the advanced Android 6.0 operation system and a powerful CPU processor, so this car radio can operate more stably and faster than your original car radio.
With the assistance of the high-accuracy GPS navigation system, you can easily know your current location and plan the most suitable route to arrive at your destinations through turn-by-turn directions and voice prompts. While navigating, you can make use of this unit’s dual zone function to play your favorite music, which won’t have any negative influence on GPS function.
Besides, through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone with this car radio, you can get access to both Bluetooth hands-free calls and streaming music with keeping your hands on the steering wheel and your eyes on the road ahead. Thus, you can enjoy the great convenience and enjoyment brought by GPS function.
As a car owner, you must want to enjoy a lot of upgraded and new features in your beloved car. In that case, you can replace your factory radio with a new aftermarket car radio. And to finish the installation, a correct installation instruction is indispensable. This article will mainly introduce a 2011 2012 2013 2014 VW GTi car radio installation instruction from Seicane to you. If you have the same or similar dashboard, please refer to it step by step.
2011 2012 2013 2014 VW GTi Car Radio with Bluetooth GPS after installation
In order to install your new head unit from Seicane you will need the following tools:
a. Panel removal tool or a flat head screw driver with a rag or cover so as to not scratch your dash
b. Torx 20 screw driver or bit, drill works as well
2011 2012 2013 2014 VW GTi car radio removal installation test instruction
1. Begin by disconnection the negative (-) terminal of your battery. For this vehicle you will need a 10mm socket or a 10mm wrench. Undue your terminal and make sure it stays disconnected until you are done with the install.
2. Please remove the trim piece around your factory radio.
Please remove the trim piece around your factory radio
Make sure to not pry only on one side as to avoid damaging or breaking your trim piece. Always start on one side and work your way around.
3. Once the trim piece is removed you will see four (4) torx screws that will need to be removed.
Once the trim piece is removed you will see four (4) torx screws that will need to be removed
4. Remove all four screws in order to gain access to the back of the radio to remove all harnesses. Then pull forward to expose back of radio.
Remove all four screws in order to gain access to the back of the radio to remove all harnesses. Then pull forward to expose back of radio
5. With radio pulled forward you can start by removing all harnesses. For this specific vehicle we will remove two antennas (am/fm and satellite) as well as the main harness.
With radio pulled forward you can start by removing all harnesses. For this specific vehicle we will remove two antennas (am/fm and satellite) as well as the main harness
To remove both antennas, please firstly press down on the tab then pull back. This works for both satellite “seen in above pic with green connector” and the AM/FM antenna “seen above in with white connector”
To remove the main harness, press down on the tab located inside the black connector, then pull black lever located at bottom of harness to release it from the radio “see following pic”
5-1
6. Once all three connecting harness has been removed you can set your factory radio off to the side as it will not be needed.
Now you will have the three (3) or more connecting harnesses ready for your new Seicane radio.
Now you will have the three (3) or more connecting harnesses ready for your new Seicane radio.
7. To begin the installation of your new radio, you will need to find a place for your GPS antenna. In this installation we will install it behind the middle two vents.
If you choose this location, begin by removing the two (2) torx 20 screws located right below them.
If you choose this location, begin by removing the two (2) torx 20 screws located right below them
8. Once removed, using your fingers and the panel removal tool push/pull up and forward to release the vents. It may seem really hard at first as there are four metal clips holding it in place. Just remember to not pry more on one side as to avoid damage to your car parts.
Once removed, using your fingers and the panel removal tool push/pull up and forward to release the vents. It may seem really hard at first as there are four metal clips holding it in place. Just remember to not pry more on one side as to avoid damage to your car parts
9. Replace any clips that may have come off during the removal of the vents. Then pull on the wiring harness that connects to the hazard light switch to give you enough slack to place vents on dash.
9. Replace any clips that may have come off during the removal of the vents. Then pull on the wiring harness that connects to the hazard light switch to give you enough slack to place vents on dash.
10. Now we can place GPS antenna and using silicone “for this location of install” to prevent the antenna from moving around.
Put silicone at the base and run antenna behind and above the vents, hold in place until silicone dries. You may use other products such as hot glue as well.
With GPS antenna placed, run your wire around the left or right side and feed cable through middle opening “see below pic”.
Now we can place GPS antenna and using silicone “for this location of install” to prevent the antenna from moving around
11. Now put back your vents and screw back both torx screws. Place back in the same manner as they were removed. Make sure not to pinch the antenna wire.
Now we can begin to install the Seicane harnesses.
Now we can begin to install the Seicane harnesses
12. Start with the main harness, to connect simply pull lever up from factory harness. Push Seicane connector all the way in then push lever down to latch on both harnesses. Next Install the AM/FM harness by pushing in the one end to the factory antenna on the one side with the locking clip.
Start with the main harness, to connect simply pull lever up from factory harness. Push Seicane connector all the way in then push lever down to latch on both harnesses. Next Install the AM/FM harness by pushing in the one end to the factory antenna on the one side with the locking clip
13. Now we can connect all the harnesses to your new Seicane radio.
Now we can connect all the harnesses to your new Seicane radio
14. Here we can see the both antennas connected as well as the main power harness and other audio/video connections along with the USB.
To see which connectors go in each port see the following pics “depending on the added accessories you may have purchased this may vary”
The wiring diagram
15. Ensure all connections are placed in the correct port to avoid damage to your new Seicane radio. The following is the illustration of all the correct port connections. Make note that the two sets of aux rca cables are connected to ensure your factory aux input works.
The following is the illustration of all the correct port connections
16. In order to make this unit function properly including your Bluetooth you will need to disconnect the factory unit from your vehicle “if equipped”.
In order to make this unit function properly including your Bluetooth you will need to disconnect the factory unit from your vehicle “if equipped”
Please note: This module can be found under the passenger seat, access it by pushing the seat all the way back. Then please use your fingers pull up and forward. The styrofoam is held by Velcro so no need to worry about clips.
17. Once removed, press down on the black tab located in the middle of the white clip and pull black lever up to removed harness. Place harness back into opening to avoid rattles and damage to harness from seat.
17
18. Now you can connect the main power to your Seicane unit and place into dash “without screwing it into place”.
Reconnect the negative (-) terminal of your battery.
You will now see your Seicane unit boot up.
You will now see your Seicane unit boot up
Now your installation is completed!
You can do a quick test by scrolling on the screen and testing the sound by using the radio or other sources to ensure all connections were made properly.
19. You can now screw the unit back into place by using the original torx screws.
You can now screw the unit back into place by using the original torx screws
20. Then place back the trim piece. Place all the way around first then push left and right sides following by lower and upper sides.
Then place back the trim piece. Place all the way around first then push left and right sides following by lower and upper sides
Before installation, please make clear every detailed step. If you have any doubts, please contact your dealer, communicate with someone experienced or turn to a professional for help. Or you can straightly go to a car radio upgrade center to ask a technician to help install the new car radio.
Besides, if you are still searching for an ideal car radio for your beloved car, you can check out the following link from Seicane which is a remarkable car radio that can work well with most VW Volkswagen car models. For more details, please click:
This 2011 2012 2013 2014 VW GTi car radio is based on the stable Android 6.0 operation and a strong quad-core CPU processor, which can help you gain a much smoother, faster and more stable operation experience than ever before.
With this car radio installed in your car, a brand new driving experienced can be gained by taking great advantage of these features, including the high-end 3D GPS navigation function, FM/AM radio tuner, Bluetooth hands-free calls, Bluetooth streaming music, steering wheel control, USB ports, etc.
What are you waiting for? If you like this unit, just add it to your shopping cart right now. Wish you have a nice time accompanied by it. Good luck!
If you are looking for some ways to improve your car interior environment and upgrade your driving experience, you can consider installing a new multifunctional car radio to replace your monofunctional car radio. This article mainly introduces a 1998 1999 2000 2001 2002-2006 Mercedes Benz G Class W463 G550 G500 G400 car radio installation guide from Seicane to you. If you have the same vehicle type, and your factory radio is incompatible with many modern features you want to get access to, you can refer to the following guide to help with the installation. Wish it can be helpful for you.
1998 1999 2000 2001 2002-2006 Mercedes Benz G Class W463 G550 G500 G400 GPS Bluetooth DVD Car Radio after installation
Precautions for this installation:
1.Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.
2.Please make sure that all fastened wires are isolated with electrical tape.
3.Please make sure the ignition is off to avoid short circuit.
4.Please prepare a lever and a screwdriver before the removal and the installation.
1998 1999 2000 2001 2002-2006 Mercedes Benz G Class W463 G550 G500 G400 car radio installation guide
1. The original car radio.
The original car radio
2. Use a special plastic tool to remove the trim bazel.
Use a special plastic tool to remove the trim bazel2-1
3. Use a plastic remove tool to push up the heat vent.
Use a plastic remove tool to push up the heat vent3-1
4. Remove 2 hidden screws with a screwdriver below the vent.
Remove 2 hidden screws with a screwdriver below the vent4-1
5. Push down the vent and loose it.
Push down the vent and loose it
6. Remove the trim panel with a plastic removal tool.
Remove the trim panel with a plastic removal tool
7. Remove 2 screws that are holding the car radio.
Remove 2 screws that are holding the car radio7-1
8. Take out the original car radio.
Take out the original car radio
9. Unplug the connectors and cables at the back of the radio.
Unplug the connectors and cables at the back of the radio
10. Check all the accessories for the new Seicane car radio.
11. Connect the harnesses to the back of the new Seicane car radio.
12. Connect the Seicane car radio to your original radio’s plugs.
13. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
14. Put the new Seicane car radio into the dash.
15. Put everything into their original place. All the installation is done.
That’s all about how to remove and install a 1998 1999 2000 2001 2002-2006 Mercedes Benz G Class W463 G550 G500 G400 car radio. If there are any questions about either you car radio or the installation, you can contact your dealer for seeking a wiring diagram or seek help from someone experienced as well as a professional. Or you can directly arrange a professional technician to help you install the new car radio. Besides, it is essential for you to check the compatibility between your new car radio and your car. If you don’t have any ideas, you can refer to this intelligent 1998 1999 2000 2001 2002-2006 Mercedes Benz G Class W463 G550 G500 G400 car radio from Seicane. Please click:
This top 1998 1999 2000 2001 2002-2006 Mercedes Benz G Class W463 G550 G500 G400 car radio, integrated with practical and entertainment features, can be regarded as one of the replacements for your factory radio. So you are able to embrace a brand new driving experience. Here I would like to introduce 3D GPS function and DVD player function.
With the assistance of the high-accuracy 3D GPS navigation system, you are able to know your current locations and navigate to your desired destinations through turn-by-turn directions and voice prompts. Besides, as for the entertainment features, you can make full use of this unit’s DVD player function. When you easily get tired or bored during your long-time driving, this car radio enables you to play any audio and video formats which include VCD/ CD/ MP3/ MPEG4/ DIVX /CD-R/ WMA to relax both yourself and your passengers.
If you like this unit, just add it to your shopping cart. Good luck to you!
If you want to pursue a more convenient and comfortable in-car life as well as a brand new driving experience, as far as I am concerned, it is the easiest and best way for you to replace your factory radio with a new multifunctional car radio. The following is a detailed 2008 2009 2010 2011 2012-2014 Mercedes Benz GLK X204 GLK350 GLK320 GLK280 GLK250 GLK220 GLK200 car radio installation guide. If you have the same or similar dashboard, you might as well refer to this guide before you start your installation work.
2008 2009 2010 2011 2012-2014 Mercedes Benz GLK X204 GPS Bluetooth Car Radio after installation
Before and during installation, you should notice:
1.Before connecting, please make sure the ignition is off to avoid short circuit.
2.Ensure connect the yellow and red power cable at last.
3.Ensure that all loose wires are isolated with electrical tape
4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
5.Ensure that all ground is connected to the same place.
6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.
2008 2009 2010 2011 2012-2014 Mercedes Benz GLK X204 GLK350 GLK320 GLK280 GLK250 GLK220 GLK200 car radio installation guide
1. The original car radio.
The original car radio
2. Use a flat removal tool to pry up the air vent.
Use a flat removal tool to pry up the air vent
3. Remove the air vent and disconnect the connector at the back of the air vent.
Remove the air vent and disconnect the connector at the back of the air vent3-1
4. Use the flat removal tool to pry the screen panel.
Use the flat removal tool to pry the screen panel4-1
5. Use a screwdriver to remove screws that are holding teh screen.
Use a screwdriver to remove screws that are holding teh screen5-1
6. Pry the car radio panel.
Pry the car radio panel
7. Remove the screws that are holding the car radio.
Remove the screws that are holding the car radio7-1
8. Use a removal tool to help you remove the original car radio.
Use a removal tool to help you remove the original car radio
9. Take the original car radio out from the dashboard.
Take the original car radio out from the dashboard
10. Disconnect the connectors and cables at the back of the original car radio.
Disconnect the connectors and cables at the back of the original car radio
11. Check all the accessories for the new Seicane car radio.
Check all the accessories for the new Seicane car radio
12. Connect the harnesses to the back of the new Seicane car radio.
Connect the harnesses to the back of the new Seicane car radio
13. Connect the Seicane car radio to your original car radio’s plugs.
14. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
15. If the new Seicane car radio works well, put it into the dash.
16. Put everything into their original place, and all the installation is done.
It is normal if you encounter any problems during the installation process. In that case, it is suggested that you should contact your dealer, communicate with someone experienced or turn to a professional for help. Or you can directly go to a car radio upgrade center to ask a professional to help you install the new car radio.
This car radio can enhance it capacity, improve its performance and facilitate its operation since it is upgraded to run on the stable Android 6.0 operation system and a high-quality 8 – Core 1.5 GHz RK-PX5 A53 processor.
Both your car interior environment and driving experience can be greatly improved thanks to these features supported by this unit, mainly including the high-end 3D GPS navigation function, FM/AM radio, DVD player, Bluetooth hands-free call, Bluetooth streaming music, AUX, USB/ SD connection, etc.
Even though you don’t have a good sense of directions, you can depend on the 3D GPS navigation system of high accuracy to locate where you are and find the right way to reach your desired destinations through turn-by-turn directions and voice prompts. Additionally, this unit’s dual zone function enables you to listen to your favorite music while navigating.
Wish you enjoy your driving accompanied by this unit. Good luck to you!
There is no denying that with a remarkable car stereo installed in your car, your in-car life can be taken up a notch. Therefore, more and more car owners are trying to replace their factory radio with a new aftermarket car stereo so as to get access to a lot of upgraded and brand new features. Today I would like to share a detailed 2006 2007 2008 2009 2010-2011 Honda Civic car stereo installation instruction from Seicane with you. If you also own a 2006 2007 2008 2009 2010-2011 Honda Civic, you might as well read the following instruction carefully.
2006 2007 2008 2009 2010-2011 Honda Civic Car Stereo Audio after installation
Before and during installation, you should notice:
1.Before connecting, please make sure the ignition is off to avoid short circuit.
2.Ensure connect the yellow and red power cable at last.
3.Ensure that all loose wires are isolated with electrical tape
4.Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
5.Ensure that all ground is connected to the same place.
6.Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.
2. Pry the cover of the slot below the CD player with a lever and remove it.
Pry the cover of the slot below the CD player with a lever and remove it
3. Remove two screws inside the slot with a ninety-degree screwdriver.
Remove two screws inside the slot with a ninety-degree screwdriver
4. Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel.
Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel
5. Remove one screw in the dash.
Remove one screw in the dash
6. Remove the vent panel.
Remove the vent panel
7. Unplug the connectors beneath the panel.
Unplug the connectors beneath the panel
8. Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash.
Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash
9. Unplug the connectors at the back of the original radio.
Unplug the connectors at the back of the original radio9-1
10. Disconnect the antenna and the other connector on the other side of the original radio.
Disconnect the antenna and the other connector on the other side of the original radio10-1
11. Check all the accessories for the new Seicane car stereo.
12. Connect the harnesses to the back of the new Seicane car stereo.
13. Connect the Seicane car stereo to your original car radio’s plugs.
14. Put the new Seicane car stereo into the dash.
15. Turn on the new Seicane car stereo and check whether the unit is working properly.
Wish the above installation instruction can do you some help. If you have any doubts, please don’t hesitate to contact your dealer, communicate with someone experienced or turn to a professional for help. Or for avoiding damage to either your car stereo or your car, you’d better go to a car stereo upgrade center to ask a technician to help you install the new car stereo.
Anyway, before installation, please make sure you’ve had an ideal car stereo. If not, I’d like to recommend an excellent 2006 2007 2008 2009 2010-2011 Honda Civic car stereo from Seicane to you. For more details, please click:
Loaded with the stable Android 6.0 operation system and a powerful 8-core 1.5 GHz RK-PX5 A53 processor, this car stereo can be regarded as the best replacement for your factory radio because of its enhanced and improved capacity and performance.
The built-in GPS navigation system of this car stereo makes it easier for you to locate where you are and find the right way to reach your desired destinations through turn-by-turn direction and voice prompts. Besides, while navigating, you can also enjoy your favorite music thanks to this unit’s dual zone function.
Besides, through the wireless Bluetooth connection between your Bluetooth-enabled mobile phone and this unit, you can dial, answer, reject and mute hands-free calls as well as listen to your favorite music streaming from your phone music playlists, which add both convenience and enjoyment to your in-car life.
Wish you enjoy your driving experience accompanied by this car stereo. Good luck to you!
The steady technology development makes it possible for people to enjoy the latest and the most advanced features with a certain amount of money. Nowadays, to have an ideal in-car environment and enjoy more convenience, more and more car owners choose to replace their factory radio with new multifunctional car radios. This article will introduce a 2006 2007 2008 2009 2010 2011 2012 Toyota Rav4 car radio installation instruction from Seicane. If you own the same car model, you can refer to this instruction carefully to help with your installation in the future.
2006 2007 2008 2009 2010 2011 2012 Toyota Rav4 GPS Bluetooth DVD Car Radio after installation
Before and during installation, you should notice:
1. Before connecting, please make sure the ignition is off to avoid short circuit.
2. Ensure connect the yellow and red power cable at last.
3. Ensure that all loose wires are isolated with electrical tape
4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
5. Ensure that all ground is connected to the same place.
6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.
2009 2010 2011 2012 Toyota Rav4 car radio installation instruction
1. The original car radio.
The original car radio
2. Remove the panel by using plastic removal tool.
Remove the panel by using plastic removal tool
3. Unplug the hazard warning lights.
Unplug the hazard warning lights
4. Remove the left panel and unplug the switch.
Remove the left panel and unplug the switch
5. Unplug the switch.
Unplug the switch
6. Remove four screws.
Remove four screws6-1 a. Position for screws.
7. Pull out the factory radio.
Pull out the factory radio
8. The back of the original car radio.
The back of the original car radio
9. Remove 8 screws from original car radio.
Remove 8 screws from original car radio9-1
10. Remove 2 screws at the top of the new radio.
Remove 2 screws at the top of the new radio10-1
11. Install 8 screws to new car radio.
Install 8 screws to new car radio
12. Plug into factory plugs.
Plug into factory plugs
13. All plugs after connection.
All plugs after connection13-1
14. Check all the accessories for the new Seicane car radio.
Check all the accessories for the new Seicane car radio
15. Connect the harnesses to the back of the new Seicane car radio.
Connect the harnesses to the back of the new Seicane car radio
16. Connect the Seicane car radio to your original car radio ‘s plugs.
17. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
18. If the new Seicane car radio works well, put it into the dash.
19. Put everything into their original place, and all the installation is done.
Wish the above installation instruction can be helpful for you. If you have any doubts, just don’t hesitate to consult your dealer, communicate with someone experienced or turn to a professional for help. If you still think the installation process is too complicated for you to finish by yourself, you can also straightly go to a car radio upgrade center and ask a technician to help you install the new car radio. Moreover, if you are still looking for a suitable car radio but don’t know what kind of car radios can fit your car well, you might as well check out the following link which is a 2006 2007 2008 2009 2010 2011 2012 Toyota Rav4 car radio from Seicane.
Based on the stable Android 6.0 operation system, a powerful 8-core 1.5 GHz RK-PX5 A53 processor and 32 GB INand Flash as well as 2GB RAM, this car radio can provide its users with higher capacities and better performance.
When you are traveling around an unfamiliar place, even you have no good sense of directions, you can turn on the GPS function to find the right way to reach your destinations. Thanks to the high-accuracy 3D GPS navigation system, you are able to accurately arrive at your destinations by getting access to a lot of features, including landmark building display, 3D street view, destination search, turn-by-turn voice directions, etc. And thanks to dual zone function, you can freely enjoy your favorite music from radio/AV/DVD/TV etc under GPS mode.
If you like this car radio, just add it to your shopping cart. Good luck to you!
Having a comfortable in-car environment and great enjoyment is what most car owners want to pursue while they are driving cars on all trips. And now an intelligent car radio can help realize this goal. As a matter of fact, to install a new car radio is not a difficult thing for you with some related installation experience and a correct guide. The following is a 2015 Ford focus car radio installation instruction from Seicane. If you also have the same or similar dashboard, you can follow this instruction step by step.
2015 Ford focus Car Radio after installation
Tips about the installation:
1.Please disconnect the power before the installation.
2.Please prepare a lever and a screwdriver before the removal and the installation.
3.Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.
2015 Ford focus car radio installation instruction
1. The original car radio.
The original car radio
2. Remove one bar under the radio with a plastic removal tool.
Remove one bar under the radio with a plastic removal tool2-1
3. Remove two screws that fixed the trim panel.
Remove two screws that fixed the trim panel3-1
4. Gently take out the trim panel.
Gently take out the trim panel4-1
5. Remove screws fixed the radio.
Remove screws fixed the radio
6. Pull out the original car radio.
Pull out the original car radio
7. Unplug the connectors at the back of the car radio.
Unplug the connectors at the back of the car radio
8. Check all the accessories for the new Seicane car radio.
9. Connect the harnesses to the back of the new Seicane car radio.
10. Connect the Seicane car radio to your original stereo’s plugs.
11. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
12. Put the new Seicane car radio into the dash.
13. Put everything into their original place. All the installation is done.
Before the installation, please confirm that you’ve made clear every detailed step. If not, please don’t hesitate to consult your dealer for seeking advice or turn to a professional for help. Or during the installation, you can ask someone experienced to help you alongside. If you still think it hard to install the new car radio by yourself, you’d better arrange a technician to help install the car radio.
Besides, to help you select an ideal car radio, you can refer to a great 2015 Ford focus car radio from Seicane. Here comes the related link, please click:
Integrated with a wide range of practical and entertainment features, this modern multifunctional car radio will become an ideal replacement for your factory radio in 2015 Ford focus.
With the assistance of the high-end GPS navigation system, you won’t get lost even you are in a totally unfamiliar place. According to features, including current location, speed, mileage, landmark building display, 3D street view, destination search and turn-by-turn voice directions, you can be accurately guided to anywhere you would like to go.
Under the wireless Bluetooth connectivity, you can pair your Bluetooth-enabled mobile phone with this unit so as to dial, answer, reject and mute hands-free calls as well as enjoy your favorite music streaming from your phone playlists without taking your hands off the steering wheel. So you get great convenience and enjoyment.
If you like this car radio, just add this unit to your shopping cart. Wish you have a brand new driving experience accompanied by it. Good luck to you!
Recent Comments