Home › Archive for Car DVD › Page 9

Car DVD

introduce car dvd products

How to Install a 2007 2008 2009 2010-2013 Honda Fit Car Stereo to Fix Radio Problems in an Effective Way

Posted on by — 6 Comments ↓ 3,050 views
2007 2008 2009 2010-2013 Honda Fit Car Stereo after installation

If you are not satisfied with your factory radio since it cannot be compatible with some modern or upgraded features, it is suggested that you can replace your factory radio with a new aftermarket car radio. If you wonder how to install a 2007 2008 2009 2010-2013 Honda Fit car radio, then you can carefully read the following installation instruction on a 2007 2008 2009 2010-2013 Honda Fit car radio. Wish it is helpful for you.

2007 2008 2009 2010-2013 Honda Fit Car Stereo after installation
2007 2008 2009 2010-2013 Honda Fit Car Stereo after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2007 2008 2009 2010-2013 Honda Fit car radio installation instruction

1. Open the glove box at first.

Open the glove box at first
Open the glove box at first

2. Remove the four screws of gloves box as these pictures show.

Remove the four screws of gloves box as these pictures show
Remove the four screws of gloves box as these pictures show
2-2
2-2
2-3
2-3
2-4
2-4

3. Unscrew the two bolts under the radio.

Unscrew the two bolts under the radio
Unscrew the two bolts under the radio
3-2
3-2

4. Take out the original car radio.

Take out the original car radio
Take out the original car radio

5. Remove the original car radio.

Remove the original car radio
Remove the original car radio

6. Disconnect all connectors at the back of the original car radio.

Disconnect all connectors at the back of the original car radio
Disconnect all connectors at the back of the original car radio

7. Remove screws of air condition as these pictures show.

Remove screws of air condition as these pictures show
Remove screws of air condition as these pictures show
7-2
7-2
7-3
7-3
7-4
7-4
7-5
7-5

8. Pull out the air outlet of air condition.

Pull out the air outlet of air condition
Pull out the air outlet of air condition

9. Remove the hazard warning switch light.

Remove the hazard warning switch light
Remove the hazard warning switch light

10. Install the air outlet with the unit.

11. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

12. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

13. Connect the Seicane car radio to your original car radio’s plugs.

14. Turn on the new Seicane radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

15. Put the new Seicane radio into the dash.

16. Put everything into their original place. All the installation is done.

 

If you have any doubts, please feel free to consult your dealer, communicate with someone experienced or turn to a professional for help. If you still think it hard to finish the whole installation process, you’d better arrange a professional technician to help you install the new car radio straightly. Besides, if you don’t know how to select a suitable car stereo for your car, I’d like to recommend an amazing 2007 2008 2009 2010-2013 Honda Fit car radio from Seicane to you. For more details, please click:

https://www.seicane.com/2007-2008-2009-2013-honda-fit-android-hd-touchscreen-gps-navigation-system-with-bluetooth-wifi-mirror-link-steering-wheel-control-s0402

This powerful car radio is running on the stable Android 6.1 operation system and high-quality quad-core CPU processor.

Even though you are not good at identifying directions, the high-accuracy 3D GPS navigation system is specially built in to offer you some help. With the help of the worldwide real-time navigation, you can get access to features like current location, 3D street view, landmark building display, turn-by-turn voice directions, etc. So you can be accurately guided to arrive at your desired destinations.

Additionally, under the wireless Bluetooth technology, without taking your hands off the steering wheel, both Bluetooth hands-free phone calls and Bluetooth streaming music are available as long as you pair your Bluetooth-enabled mobile phone with this unit.

Wish you like this multifunctional car radio and good luck to you!

Top Installation Guide for a 2006 2007 2008 2009-2011 Honda Civic GPS Navigation Bluetooth USB WIFI Car Radio

Posted on by — No Comments ↓ 5,666 views
2006 2007 2008 2009-2011 Honda Civic Bluetooth GPS Car Radio after installation

If you plan to upgrade your factory radio so as to reduce budget by yourself, it is suggested that you should find a correct installation instruction and follow it to deal with the car radio removal and installation. The following is a 2006 2007 2008 2009-2011 Honda Civic car radio installation instruction. If you own the same or similar dashboard, you can take this instruction as a reference. Wish it is helpful for you to some extent.

2006 2007 2008 2009-2011 Honda Civic Bluetooth GPS Car Radio after installation
2006 2007 2008 2009-2011 Honda Civic Bluetooth GPS Car Radio after installation

Before and during installation, you should notice:

1. Before connecting,please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire,so when replace the fuse, please consult the professional.

7. For your convenience, here’s there commended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2006 2007 2008 2009-2011 Honda Civic car radio installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Pry the cover of the slot below the CD player with a lever and remove it.

Pry the cover of the slot below the CD player with a lever and remove it
Pry the cover of the slot below the CD player with a lever and remove it

3. Remove two screws inside the slot with a ninety-degree screwdriver.

Remove two screws inside the slot with a ninety-degree screwdriver
Remove two screws inside the slot with a ninety-degree screwdriver

4. Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel.

Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel
Pry the lower panel with a lever, loosen it with your hands at the same time, after that, remove the panel

5. Remove one screw in the dash.

Remove one screw in the dash
Remove one screw in the dash

6. Remove the vent panel.

Remove the vent panel
Remove the vent panel

7. Unplug the connectors beneath the panel.

Unplug the connectors beneath the panel
Unplug the connectors beneath the panel

8. Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash.

Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash
Pry the edges along the panel of the original radio, then remove it, after that, take the original car radio out of the dash

9. Unplug the connectors at the back of the original radio.

Unplug the connectors at the back of the original radio
Unplug the connectors at the back of the original radio
9-1
9-1

10. Disconnect the antenna and the other connector on the other side of the original radio.

Disconnect the antenna and the other connector on the other side of the original radio
Disconnect the antenna and the other connector on the other side of the original radio
10-1
10-1

11. Check all the accessories for the new Seicane car stereo.

Check all the accessories for the new Seicane car stereo
Check all the accessories for the new Seicane car stereo

12. Connect the harnesses to the back of the new Seicane car stereo.

Connect the harnesses to the back of the new Seicane car stereo
Connect the harnesses to the back of the new Seicane car stereo

13. Connect the Seicane car stereo to your original car radio’s plugs.

14. Put the new Seicane car stereo into the dash.

15. Turn on the new Seicane car stereo and check whether the unit is working properly.

 

Wish you can get some help from the above installation guide. If you have any doubts, please don’t hesitate to contact your dealer, communicate with someone experienced or turn to a professional for help. Besides, if you still think the installation process is too complicated, you can directly arrange a professional from Seicane to help you. Anyway, before installation, you should select an ideal car radio for your beloved car. If you have no ideas, here I would like to recommend a remarkable 2006 2007 2008 2009-2011 Honda Civic car radio from Seicane to you. Here comes the link, please click:

https://www.seicane.com/hd-touch-screen-android-gps-navigation-radio-for-2006-2011-honda-civic-with-bluetooth-wifi-obd2-usb-audio-aux-1080p-rearview-camera-s0411


Loaded with the advanced and stable Android 6.1 operation system and a powerful quad-core CPU processor, this car radio has greatly enhance its capabilities and performance. So with this car radio, you can gain a much smoother, faster and easier operation experience.

Under the guidance of the turn-by-turn directions and voice prompts provided by the worldwide real-time GPS navigation system of high accuracy, it will be much easier for you to locate where yo are currently and have the most suitable route option to reach your desired destinations.

Additionally, as long as you connect your Bluetooth-enabled mobile phone to this car radio, you are able to get access to Bluetooth hands-free phone calls as well as listen to streaming music for more convenience and enjoyment without taking your hands off the steering wheel.

If you like this unit, just add it to your shopping cart. Good luck!

The Useful Installation Instruction on a 2007 2008 2009 2010 Toyota OLD Corolla Car Radio with DVD Player Bluetooth GPS Navigation System

Posted on by — 2 Comments ↓ 1,135 views
2007 2008 2009 2010 Toyota OLD Corolla GPS Sat Nav Bluetooth Car Radio after installation

There is no doubt that you may feel tired or bored if you have been driving for a long time, and in that case, you must want to refresh yourself. Under this circumstance, you can listen to your favorite music, watch TV programs or play videos in your car. And your factory radio may not support these entertainment features, so you can consider replacing your factory radio with a new aftermarket car radio. The following is a 2007 2008 2009 2010 Toyota OLD Corolla car radio installation guide from Seicane. If you own the same or similar dashboard, you can refer to it carefully.

2007 2008 2009 2010 Toyota OLD Corolla GPS Sat Nav Bluetooth Car Radio after installation
2007 2008 2009 2010 Toyota OLD Corolla GPS Sat Nav Bluetooth Car Radio after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-devicesrd-400

 

2007 2008 2009 2010 Toyota OLD Corolla car radio installation guide

1. Remove the bottom panel (air conditioning) with plastic knife.

Remove the bottom panel (air conditioning) with plastic knife
Remove the bottom panel (air conditioning) with plastic knife
1-1
1-1

2. Pry the top of the original car CD panel with plastic knife.

Pry the top of the original car CD panel with plastic knife
Pry the top of the original car CD panel with plastic knife

3. Remove the four screws with a screwdriver.

Remove the four screws with a screwdriver
Remove the four screws with a screwdriver

4. Take the original radio out of the dash.

Take the original radio out of the dash
Take the original radio out of the dash

5. Pull the plug of the original radio.

Pull the plug of the original radio
Pull the plug of the original radio

6. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

7. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

8. Socket docking with the original radio directly, instead of cutting the original plug off.

Socket docking with the original radio directly, instead of cutting the original plug off
Socket docking with the original radio directly, instead of cutting the original plug off

9. Put the original radio plug into our Seicane radio.

Put the original radio plug into our Seicane radio
Put the original radio plug into our Seicane radio

10. Put the new Seicane radio back into the dash.

11. Turn on the new Seicane radio to check if all functions work well. If it doesn’t, please check whether all the cables are connected correctly.

12. Install four screws and panels into their original place.

 

Wish you can learn something useful from the above installation steps. If you come across any problems you don’t know how to deal with, you can seek help from your dealer, someone experienced or a professional. If you still think it hard to install the new car radio, you can directly arrange a professional technician to install the new car radio.

While for the selection of an ideal car radio, if you have no ideas, you can check out the following link which is an amazing 2007 2008 2009 2010 Toyota OLD Corolla car radio from Seicane.

https://www.seicane.com/2007-2008-2009-2010-toyota-old-corolla-android-bluetooth-radio-gps-navigation-head-unit-support-wifi-1080p-video-backup-camera-audio-system-dvr-obd2-s0467

This all-in-one car radio is running on the stable Android 6.1 operation system and a powerful quad-core CPU processor to enhance its capabilities, configuration and performance, so it can be regarded as one of the best replacements for your factory radio. Besides, it also comes with a wide range or practical and entertainment features, mainly including built-in 3D GPS navigation, Bluetooth hands-free phone calls, Bluetooth streaming music, FM/AM radio tuner, file management, USB or SD card connection, etc.

With the assistance of the turn-by-turn directions and voice prompts provided by the high-end 3D GPS navigation system, you are able to locate where you are and navigate to your desired destinations. And this unit’s dual zone function enables you to listen to your favorite music while navigating.

What’s more, through the Bluetooth connection between your Bluetooth-enabled mobile phone and this car radio, both Bluetooth hands-free phone calls and Bluetooth streaming music are available for you to gain more convenience and enjoyment.

If you like this unit, just add it to your shopping cart.

How to Upgrade a 2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008 Car Radio with Bluetooth GPS Navigation Proficiently

Posted on by — 6 Comments ↓ 4,071 views
2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008 Car Radio after installation

There is no doubt that among lots of ways to upgrade your car’s capabilities and performance, the most popular way is to remove your factory radio and install a brand new multifunctional car radio in your car. With such an ideal car radio in your car, you can get access to a wide range of practical and entertainment features so as to enrich your in-car life. The following is a 2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008 car radio installation guide from Seicane, which can be taken as a reference for you if you have the same or similar dashboard.

2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008 Car Radio after installation
2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008 Car Radio after installation

Before and during installation, you should notice:

1. Before connecting,please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire,so when replace the fuse, please consult the professional.

7. For your convenience, here’s there commended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008 car radio installation guide

1. The original car radio.

The original car radio
The original car radio

2. Use a plastic knife to pry the trim panel and remove it.

Use a plastic knife to pry the trim panel and remove it
Use a plastic knife to pry the trim panel and remove it
2-1
2-1
2-2
2-2

3. Remove screws that are holding the radio.

Remove screws that are holding the radio
Remove screws that are holding the radio

4. Take out the original car radio.

Take out the original car radio
Take out the original car radio

5. Disconnect the connectors and cables at the back of the radio.

Disconnect the connectors and cables at the back of the radio
Disconnect the connectors and cables at the back of the radio

6. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

7. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

8. Connect the Seicane car radio to your original radio’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

That’s all about how to remove and install the new car radio for 2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008. If you meet any problems before or during the installation, please don’t hesitate to contact your dealer, communicate with someone experienced or turn to a professional for help. If you are afraid of failing in the installation, you can directly arrange a professional technician to help you install the new car radio. Anyway, it is very essential for you to pick an ideal car radio for your beloved car. Here I would like to share an amazing 2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008 car radio from Seicane with you. You may click the following link for more details.

https://www.seicane.com/android-gps-radio-hd-touchscreen-head-unit-for-2010-2011-2012-2013-2014-2015-mitsubishi-asx-peugeot-4008-bluetooth-music-wifi-support-rearview-camera-steering-wheel-control-h601

This car radio is running on the most advanced Android 6.0 operation system and a powerful quad-core CPU processor to enhance its capabilities and performance. Therefore, with this car radio installed in your car, you will be able to embrace much smoother, faster and easier operation experience.

With this car radio installed in your car, you will enjoy a lot of practical and entertainment features, mainly including high-end 3D GPS navigation system, FM/AM radio tuner, Bluetooth hands-free phone calls, Bluetooth streaming music, file management, etc. Thanks to these features, you are able to have a more convenient and relaxing driving experience.

Under the guidance of the turn-by-turn directions and voice prompts provided by the high-end 3D GPS navigation system, you are able to easily locate where you are and find the right way to reach any locations you would like go to go without getting lost any longer. And while navigating, you can also listen to your favorite music.

If you like this unit, just add it to your shopping cart right now. Good luck!

Great Tutorial on a 2004 2005 2006 2007-2009 Mazda 3 Radio Removal to Install an Audio Stereo Sound System

Posted on by — 8 Comments ↓ 14,756 views
2004 2005 2006 2007-2009 Mazda 3 Radio after installation

If you would like to pursue a more comfortable and convenient in-car life, it will be one of the most prevailing ways for you to replace your factory radio with a new aftermarket car radio which comes with a wide range of practical and entertainment features. If you know how to install a new ca rradio, you may find it very easy for you to upgrade a car radio. The following is a 2004 2005 2006 2007-2009 Mazda 3 car radio installation instruction from Seicane. If you own the same or similar dashboard, then you can refer to this instruction carefully.

2004 2005 2006 2007-2009 Mazda 3 Radio after installation
2004 2005 2006 2007-2009 Mazda 3 Radio after installation

Precautions for this installation:

1. Before you start up any work, park your car well and unplug the negative power cable to avoid any danger.

2. Please make sure that all fastened wires are isolated with electrical tape.

3. Please make sure the ignition is off to avoid short circuit.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2004 2005 2006 2007-2009 Mazda 3 car radio installation instruction

1. Remove the trim panel with a plastic removal tool.

Remove the trim panel with a plastic removal tool
Remove the trim panel with a plastic removal tool
1-1
1-1

2. Remove two screws that fixed the car radio on the dashboard.

Remove two screws that fixed the car radio on the dashboard
Remove two screws that fixed the car radio on the dashboard

3. Take out the original car radio.

Take out the original car radio
Take out the original car radio

4. Unplug connectors at the back of the original car radio.

Unplug connectors at the back of the original car radio
Unplug connectors at the back of the original car radio
4-1
4-1

5. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

6. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

7. Connect the Seicane car radio to your original radio’s plugs.

8. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

9. Put the new Seicane car radio into the dash.

10. Put everything into their original place. All the installation is done.

 

Now do you have a general understanding of the above installation steps? If you meet any problems about either the car radio installation process pr the car radio, please don’t hesitate to contact your dealer, communicate with someone experienced or turn to a professional for help. You can straightly go to a car radio upgrade center and get the new car radio installed by a professional technician.

Besides, it is especially significant for you to pick an ideal car radio for your beloved car. If you have no ideas, you can check out the following link which is an amazing 2004 2005 2006 2007-2009 Mazda 3 car radio from Seicane. For more details, please click:

https://www.seicane.com/android-2004-2009-mazda-3-gps-navigation-car-radio-with-bluetooth-3g-wifi-usb-touch-screen-rearview-camera-mirror-link-obd2-s0477

With this car radio installed in your beloved car, you will definitely embrace a brand new driving experience so as to enjoy more convenience and enjoyment.

Under the guidance of the turn-by-turn directions and voice prompts provided by the high-end 3D GPS navigation system, you are able to easily locate where you are and navigate to any locations you would like to go to without getting lost any more.

Additionally, under the wireless Bluetooth technology, you can make your Bluetooth-enabled mobile phone pair with this car radio. By doing so, you can dial, answer, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from phone without taking your hands off the steering wheel control.

Wish you like this unit and good luck to you!

Top Remove and Upgrade tutorial for a 2004 2005 2006 2007-2010 Toyota Sienna GPS Navigation Bluetooth WIFI Car Stereo

Posted on by — 2 Comments ↓ 3,875 views
2004 2005 2006 2007 -2010 Toyota Sienna Car Stereo after installation

There is no doubt that a car radio can play a very significant part in driving experience. If you are not so satisfied with your outdated factory radio due to its simple functions, it is suggested that you should upgrade your factory radio by installing a new aftermarket car stereo. To achieve the whole installation process, you need a detailed installation instruction to guide you. Here I would like to share an easy-to-understand installation instruction on a 2004 2005 2006 2007-2010 Toyota Sienna car stereo from Seicane with you. Wish you can get some help from this instruction.

2004 2005 2006 2007 -2010 Toyota Sienna Car Stereo after installation
2004 2005 2006 2007 -2010 Toyota Sienna Car Stereo after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2004 2005 2006 2007-2010 Toyota Sienna car stereo installation instruction

1. The original car radio for 2004-2010 Toyota Sienna.

The original car radio for 2004-2010 Toyota Sienna
The original car radio for 2004-2010 Toyota Sienna

2. Use a flat-head screwdriver or a flat pry tool to pry up the vertical panels of the right and left side of the original car radio and climate control system.

Use a flat-head screwdriver or a flat pry tool to pry up the vertical panels of the right and left side of the original car radio and climate control system
Use a flat-head screwdriver or a flat pry tool to pry up the vertical panels of the right and left side of the original car radio and climate control system

3. Disconnect the wiring from the side panels. There are two wiring connectors on the left panel and only one connector on the right panel. Please carefully press the tab to release the connectors.

Disconnect the wiring from the side panels. There are two wiring connectors on the left panel and only one connector on the right panel. Please carefully press the tab to release the connectors
Disconnect the wiring from the side panels. There are two wiring connectors on the left panel and only one connector on the right panel. Please carefully press the tab to release the connectors
3-1
3-1

4. Remove the center channel speaker grill panel above the car radio. Please use a pry tool or a flat head screwdriver to pry up the top (center channel speaker) panel above the car radio and then remove it.

Remove the center channel speaker grill panel above the car radio. Please use a pry tool or a flat head screwdriver to pry up the top (center channel speaker) panel above the car radio and then remove it
Remove the center channel speaker grill panel above the car radio. Please use a pry tool or a flat head screwdriver to pry up the top (center channel speaker) panel above the car radio and then remove it
4-1
4-1

5. Remove the center speaker. There are two 10mm hex head nuts securing the center speaker, so you need to use a 10-mm Hollow-Shank nut screwdriver to remove these two bolts.

Remove the center speaker. There are two 10mm hex head nuts securing the center speaker, so you need to use a 10-mm Hollow-Shank nut screwdriver to remove these two bolts
Remove the center speaker. There are two 10mm hex head nuts securing the center speaker, so you need to use a 10-mm Hollow-Shank nut screwdriver to remove these two bolts

6. Disconnect the speaker wiring harness. Please press the tab down so as to release the wiring connector, and then set the speaker and bolts aside.

Disconnect the speaker wiring harness. Please press the tab down so as to release the wiring connector, and then set the speaker and bolts aside
Disconnect the speaker wiring harness. Please press the tab down so as to release the wiring connector, and then set the speaker and bolts aside

7. Remove the 4 10mm hex head nuts from the car radio. There are 4 bolts holding the car radio in the dash (2 on each side). Please use a screwdriver to remove these four bolts.

Remove the 4 10mm hex head nuts from the car radio. There are 4 bolts holding the car radio in the dash (2 on each side). Please use a screwdriver to remove these four bolts
Remove the 4 10mm hex head nuts from the car radio. There are 4 bolts holding the car radio in the dash (2 on each side). Please use a screwdriver to remove these four bolts
7-1
7-1

8. Gently pull the original car radio out of the dash and then disconnect the wiring from the original car radio. Then put the original car radio aside.

Gently pull the original car radio out of the dash and then disconnect the wiring from the original car radio. Then put the original car radio aside
Gently pull the original car radio out of the dash and then disconnect the wiring from the original car radio. Then put the original car radio aside
8-1
8-1

9. If necessary, please remove the left and right radio mounting brackets to install on the new Seicane car radio.

If necessary, please remove the left and right radio mounting brackets to install on the new Seicane car radio
If necessary, please remove the left and right radio mounting brackets to install on the new Seicane car radio

10. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

11. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

12. Connect the Seicane car radio to your original car radio’s plugs.

Connect the Seicane car radio to your original car radio's plugs
Connect the Seicane car radio to your original car radio’s plugs

13. Gently place the new Seicane car radio into the opening of the dash and test it.

14. Re-seat the stereo in the dash and reinstall the 4 bolts.

15. Carefully reconnect the center speaker and reinstall the 2 bolts.

Carefully reconnect the center speaker and reinstall the 2 bolts
Carefully reconnect the center speaker and reinstall the 2 bolts

16. Carefully reinstall top center channel speaker grill panel.

Carefully reinstall top center channel speaker grill panel
Carefully reinstall top center channel speaker grill panel

17. Reconnect all the electrical connectors and then reinstall the left and right side panels.

 

Don’t worry if you encounter any problems before or during the installation. To deal with these problems, you can try to seek help from your dealer, someone experienced or turn to a professional for help. If you still think it hard for you to remove your factory radio and install the new car radio, you can directly go to a car radio upgrade center and arrange a professional technician to help you install the new car radio. Anyway, it is essential for you to select an ideal car radio before installation, if you have no ideas, here I would like to recommend a remarkable 2004 2005 2006 2007-2010 Toyota Sienna car stereo from Seicane to you. Wish you will like it. For more details, please click:

https://www.seicane.com/android-gps-navigation-system-for-2004-2010-toyota-sienna-with-dvd-player-backup-camera-hd-touch-screen-3g-wifi-steering-wheel-control-bluetooth-s063812y

With this remarkable car radio installed in your car, your driving experience will absolutely be taken up a notch. This car radio is loaded with the most advanced Android 8.0 operations system and a powerful eight-core CPU processor, which will enables you to have a much smoother, faster and easier operation experience.

Under the guidance of the turn-by-turn directions and voice prompts provided by the worldwide real-time GPS navigation system, this unit enables you to easily locate where you are and help you find the right way to get to any locations you would like to go to. And this unit also comes with dual zone function, which enables you to listen to your favorite music while navigating.

Additionally, you are able to dial, receive, reject and mute Bluetooth hands-free phone calls as well as listen to Bluetooth streaming music from your phone music playlist as long as you connect your Bluetooth-enabled mobile phone to this unit.

Wish you like this car radio. Good luck!

How to Upgrade a 2005 2006 2007 2008-2013 Suzuki Vitara Car Stereo with Aux Input Bluetooth Navigation System

Posted on by — 7 Comments ↓ 4,554 views
2005 2006 2007 2008-2013 Suzuki Vitara Car Stereo after installation

If you would like to make your car get more featured, it will be a great idea for you to replace your factory radio with a brand new multifunctional car radio. And about the removal and installation, if you would like to have a try, you can search for a related installation instruction and refer to it carefully. The following is a 2005 2006 2007 2008-2013 Suzuki Vitara car radio installation instruction from Seicane, which I would like to share with you. If you own the same or similar dashboard, you can carefully follow this instruction to deal with the installation.

2005 2006 2007 2008-2013 Suzuki Vitara Car Stereo after installation
2005 2006 2007 2008-2013 Suzuki Vitara Car Stereo after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

2005 2006 2007 2008-2013 Suzuki Vitara car radio installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Open the storage box. Grasp two side panels and remove them. Please use a plastic removal tool if necessary.

3. Unscrew mounting screws that are holding the radio and the AC control.

Unscrew mounting screws that are holding the radio and the AC control
Unscrew mounting screws that are holding the radio and the AC control
3-1
3-1

4. Pull the original radio out from the dash.

Pull the original radio out from the dash
Pull the original radio out from the dash

5. Unplug the connectors and cables at the back of the radio.

Unplug the connectors and cables at the back of the radio
Unplug the connectors and cables at the back of the radio

6. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

7. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

8. Connect the Seicane car radio to your original radio’s plugs.

9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

10. Put the new Seicane car radio into the dash.

11. Put everything into their original place. All the installation is done.

 

Wish you can get some skills from the above installation instruction. If you come across any problems, you can consult your dealer, communicate with someone experienced or turn to a professional for help. Or you can straightly go to a car radio upgrade center to ask a professional technician to help you install the new car radio. Anyway, before installation, it is essential for you to select an ideal car radio before installation. If you have no ideas, here I would like to share an amazing 2005 2006 2007 2008-2013 Suzuki Vitara car radio from Seicane with you. For more details, please click:

https://www.seicane.com/android-radio-gps-navigation-system-for-2005-2013-suzuki-vitara-with-dvd-player-bluetooth-hd-1024-600-touch-screen-obd2-dvr-rearview-camera-tv-1080p-video-3g-wifi-ipod-mirror-link-steering-wheel-control-usb-sd-s167056g

Upgraded to the most advanced Android 8.0 operation system and a powerful eight-core CPU processor, this car radio specific for 2005 2006 2007 2008-2013 Suzuki Vitara will make your operation get much smoother, faster and easier.

With the assistance of the world-wide real-time GPS navigation system of high-precision, according to turn-by-turn directions and voice prompts, you are able to locate your current locations accurately and quickly plan the most suitable route to get to your desired destinations.

Besides, when you add a one DIN DVD player to this car radio, you can freely play your favorite music, TV programs, videos, movies, etc, which will add a lot of joyfulness to your trip.

This car radio is at a reasonable price right now. If you like it, just don’t hesitate to add it to your shopping cart.

How to Install a 1998 1999 2000 2001-2006 BMW 3 Series M3 E46 316i 318i 320i 323i 325i Car Stereo to Fix Radio Problems in an Effective Way

Posted on by — No Comments ↓ 3,793 views
1998 1999 2000 2001-2006 BMW 3 Series M3 E46 316i 318i 320i 323i 325i Car Stereo after installation

Have you ever thought about removing your factory radio and installing a brand new multifunctional car radio for your beloved car? If yes, you can search online for a related car radio and read it carefully to have a general understanding of the car radio installation. The following is a 1998 1999 2000 2001-2006 BMW 3 Series M3 E46 316i 318i 320i 323i 325i car radio installation guide from Seicane, which can be taken as your reference if you own the same or similar dashboard. Wish this guide is helpful for you.

1998 1999 2000 2001-2006 BMW 3 Series M3 E46 316i 318i 320i 323i 325i Car Stereo after installation
1998 1999 2000 2001-2006 BMW 3 Series M3 E46 316i 318i 320i 323i 325i Car Stereo after installation

Before and during installation, you should notice:

1. Before connecting, please make sure the ignition is off to avoid short circuit.

2. Ensure connect the yellow and red power cable at last.

3. Ensure that all loose wires are isolated with electrical tape

4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).

5. Ensure that all ground is connected to the same place.

6. Using the improper fuse may cause damage of fire, so when replace the fuse, please consult the professional.

7. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

1998 1999 2000 2001-2006 BMW 3 Series M3 E46 316i 318i 320i 323i 325i car stereo installation instruction

1. The original car radio.

The original car radio
The original car radio

2. Remove the surrounding trim panel with a plastic removal tool.

Remove the surrounding trim panel with a plastic removal tool
Remove the surrounding trim panel with a plastic removal tool
2-1
2-1
2-2
2-2

3. Remove two screws fixed the radio on the dashboard.

Remove two screws fixed the radio on the dashboard
Remove two screws fixed the radio on the dashboard
3-1
3-1

4. Gently pull out the original car radio.

Gently pull out the original car radio
Gently pull out the original car radio

5. Unplug the connectors and cables at the back of the radio.

Unplug the connectors and cables at the back of the radio
Unplug the connectors and cables at the back of the radio

6. Remove the A/C control and unplug the connectors.

Remove the A/C control and unplug the connectors
Remove the A/C control and unplug the connectors
6-1
6-1

7. Remove two screws holding the heat vent.

Remove two screws holding the heat vent
Remove two screws holding the heat vent
7-1
7-1

8. Remove screws so as to remove radio frame.

Remove screws so as to remove radio frame
Remove screws so as to remove radio frame

9. Check all the accessories for the new Seicane car radio.

10. Connect the harnesses to the back of the new Seicane car radio.

11. Connect the Seicane car radio to your original radio’s plugs.

12. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

13. Put the new Seicane car radio into the dash.

14. Put everything into their original place. All the installation is done.

 

Wish the above installation guide can be helpful for your installation to some degree. If you encounter any problems you cannot deal with by yourself, please feel free to contact your dealer, communicate with someone experienced or turn to a professional for help. If you still think it hard for you to finish the whole installation process, you’d better arrange a technician to help you install the new car radio.

Besides, it is very crucial for you to select an ideal car radio for your beloved car. If you have no ideas, you can refer to the following link which is an amazing 1998 1999 2000 2001-2006 BMW 3 Series M3 E46 316i 318i 320i 323i 325i car radio from Seicane. Here comes the related link, please click:

https://www.seicane.com/radio-hd-touchscreen-android-for-1998-2006-bmw-3-series-m3-e46-316i-318i-320i-323i-325i-gps-navigation-system-with-wifi-bluetooth-usb-mirror-link-rearview-aux-s129006e

This car radio is running on the newest Android 8.0 operation system, a high-quality 8-core 1.5 GHz RK-PX5 A53 processor, and 32GB INand Flash as well as 4GB RAM. With this car radio installed in your car, you will embrace a brand new driving life.

Even though you are not good at identifying directions, you won’t get lost any more thanks to this car radio. Under the guidance of the turn-by-turn directions and voice prompts provided by the worldwide real-time GPS navigation system, you are able to locate where you are currently and find the right way to arrive at your desired destinations. And this unit comes with dual zone function, so you can freely listen to your favorite music while navigating.

Additionally, under the wireless Bluetooth technology, without taking your hands off the steering wheel, both Bluetooth hands-free phone calls and Bluetooth streaming music are available for you as long as you pair your Bluetooth-enabled mobile phone with this unit.

If you like this unit, just don’t hesitate to add it to your shopping cart.

How to Upgrade 2011 2012 2013 2014 2015 2016 JEEP Wrangler Car Stereo with GPS Navigation Bluetooth Audio System

Posted on by — No Comments ↓ 2,501 views
2011 2012 2013 2014 2015 2016 JEEP Wrangler Car Stereo after installation

As a car owner of a 2011 2012 2013 2014 2015 2016 JEEP Wrangler, are you still looking for some way to take your driving experience up a notch? As far as I am concerned, it will be a great choice for you to remove your factory radio and install a new aftermarket car radio under a correct installation guide. This article aims to introduce how to remove the factory radio and install the new car radio for 2011 2012 2013 2014 2015 2016 JEEP Wrangler. You may refer to it carefully.

2011 2012 2013 2014 2015 2016 JEEP Wrangler Car Stereo after installation
2011 2012 2013 2014 2015 2016 JEEP Wrangler Car Stereo after installation

Here are some tips about the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and www.seicane.com make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, you can shop at Seicane.

 

2011 2012 2013 2014 2015 2016 JEEP Wrangler car radio installation instruction

1. Get the window control out of the original place, so that you can get access to the screw that is behind it.

Get the window control out of the original place, so that you can get access to the screw that is behind it
Get the window control out of the original place, so that you can get access to the screw that is behind it

2. Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control.

Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control
Here we use a precision flat-head screwdriver with cotton cloth, which make sure it not to scratch the window control
2-1
2-1

3. You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out.

You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out
You may start from the corner, which makes it easier for you to get behind and you should be able to pop it up and make it come right out
3-1
3-1

4. There is a clip and you need to push it down and make it come right off, after that, put this window control to the side.

There is a clip and you need to push it down and make it come right off, after that, put this window control to the side
There is a clip and you need to push it down and make it come right off, after that, put this window control to the side
4-1
4-1
4-2
4-2
4-3
4-3

5. Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray.

Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray
Use a seven millimeter screwdriver socket to remove the bolt behind the window control and the in the upper tray
5-1
5-1
5-2
5-2

6. Next you are going to pull away the trim under the steering wheel.

Next you are going to pull away the trim under the steering wheel
Next you are going to pull away the trim under the steering wheel
6-1
6-1

7. With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set.

With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set
With the trim removed, you are going to remove two bolts on either side of the steering column with a seven millimeter socket set

8. Firmly pull the dash and it should be clipped out.

Firmly pull the dash and it should be clipped out
Firmly pull the dash and it should be clipped out
8-1
8-1

9. With the dash removed, you now can have access to the four bolts that are holding the original car radio.

With the dash removed, you now can have access to the four bolts that are holding the original car radio
With the dash removed, you now can have access to the four bolts that are holding the original car radio

10. Remove these four bolts with the seven millimeter screwdriver.

Remove these four bolts with the seven millimeter screwdriver
Remove these four bolts with the seven millimeter screwdriver

11. With all the bolts removed, the original car radio should simply slide out from the original place.

With all the bolts removed, the original car radio should simply slide out from the original place
With all the bolts removed, the original car radio should simply slide out from the original place
11-1
11-1

12. Disconnect the factory connectors and wires at the back of the original car radio.

Disconnect the factory connectors and wires at the back of the original car radio
Disconnect the factory connectors and wires at the back of the original car radio

13. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

14. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

15. Connect the Seicane car radio to your original radio’s plugs.

16. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

17. Put the new Seicane car radio into the dash.

18. Put everything into their original place. All the installation is done.

 

Above is the whole installation process about 2011 2012 2013 2014 2015 2016 JEEP Wrangler car radio. Before removal and installation, make sure you are clear about every detailed step. If you cannot totally understand these steps, you can seek help from your dealer, someone experienced or a professional. While for the selection of an ideal car radio, if you have no ideas, here I would like to share an amazing 2011 2012 2013 2014 2015 2016 JEEP Wrangler car radio from Seicane with you.

This car radio is running on the stable Android 10.0 operation system, and it has 4G RAM and 64G ROM, so it can provide its users with smoother, faster and easier operation experience.

Under the guidance of the high-end 3D GPS navigation system, this amazing car radio enables you to locate where you are currently and find the right way to reach your desired destinations. And this unit’s dual zone function enables you to listen to your favorite music while navigating.

Additionally, the wireless Bluetooth technology for hands-free calls and streaming music is also supported by this unit to promise your driving safety and enjoyment as long as you connect your Bluetooth-enabled mobile phone to this unit.

What’s more, this unit can support the steering wheel control, headlamp output, reverse output and ACC output. And this unit can support hand brake detecting, the door information display and the original car’s amplifier.

Don’t hesitate to add it to your shopping cart if you like this unit! Good luck to you!

Top Tricks on a 1998 1999 2000 2001-2005 Mercedes-Benz CL-Class W215(CL600, CL550, CL55 AMG) GPS Bluetooth Car Stereo Installation

Posted on by — 4 Comments ↓ 5,221 views
1998 1999 2000 2001-2005 Mercedes-Benz CL-Class W215(CL600, CL550, CL55 AMG) GPS Bluetooth Car Stereo after installation

Nowadays, there is a trend that more and more car owners would like to replace their factory radio with a new aftermarket car radio, which can help them gain convenience and entertainment so as to enrich their in-car life. The following is a 1998 1999 2000 2001-2005 Mercedes-Benz CL-Class W215(CL600, CL550, CL55 AMG) car radio installation guide from Seicane for a 1998 1999 2000 2001-2005 Mercedes-Benz CL-Class W215(CL600, CL550, CL55 AMG) car radio. If you have the same or similar dashboard, you may read it carefully to deal with the installation.

1998 1999 2000 2001-2005 Mercedes-Benz CL-Class W215(CL600, CL550, CL55 AMG) GPS Bluetooth Car Stereo after installation
1998 1999 2000 2001-2005 Mercedes-Benz CL-Class W215(CL600, CL550, CL55 AMG) GPS Bluetooth Car Stereo after installation

Some tips before the installation:

1. Please disconnect the power before the installation.

2. Please prepare a lever and a screwdriver before the removal and the installation.

3. Please keep all the separate parts from the car. Please take great care of the dashboard to avoid scratching it during its detachment and installation. Please keep handy any parts from the car and make use of all the original screws from the car as much as possible. so each related part of the unit can be fixed securely.

4. For your convenience, here’s the recommended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400

 

1998 1999 2000 2001-2005 Mercedes-Benz CL-Class W215(CL600, CL550, CL55 AMG) car radio installation guide

1. The original car radio.

The original car radio
The original car radio

2. Place the key in the ignition, set the parking brake and shift to a lower gear depressing the brake.

3. Open up the pocket down below the AC control and remove two T20 Torx screws on the two corners. Then remove the pocket.

Open up the pocket down below the AC control and remove two T20 Torx screws on the two corners. Then remove the pocket
Open up the pocket down below the AC control and remove two T20 Torx screws on the two corners. Then remove the pocket

4. Grasp the bottom of the radio trim panel while prying the edges of the panel up along the sides of the dash. Then remove the panel.

Grasp the bottom of the radio trim panel while prying the edges of the panel up along the sides of the dash. Then remove the panel
Grasp the bottom of the radio trim panel while prying the edges of the panel up along the sides of the dash. Then remove the panel

5. Remove four T20 Torx screws that are holding the radio on the dashboard.

Remove four T20 Torx screws that are holding the radio on the dashboard
Remove four T20 Torx screws that are holding the radio on the dashboard

6. Pull the car radio out from the dash.

Pull the car radio out from the dash
Pull the car radio out from the dash

7. Disconnect the connectors and cables at the back of the radio.

Disconnect the connectors and cables at the back of the radio
Disconnect the connectors and cables at the back of the radio

8. Check all the accessories for the new Seicane car radio.

Check all the accessories for the new Seicane car radio
Check all the accessories for the new Seicane car radio

9. Connect the harnesses to the back of the new Seicane car radio.

Connect the harnesses to the back of the new Seicane car radio
Connect the harnesses to the back of the new Seicane car radio

10. Connect the Seicane car radio to your originalradio’s plugs.

11. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.

12. Put the new Seicane car radio into the dash.

13. Put everything into their original place. All the installation is done.

 

Before installation, please make clear every detailed step. If you have any doubts, please don’t hesitate to seek help from your dealer, someone experienced or a professional. Besides, if you still think it hard for you to install the new car radio, you can directly go to a car radio upgrade center and get the new car radio installed by a professional. Anyway, before installation, please carefully pick an ideal car radio for your beloved car. Here I would like to share a remarkable 1998 1999 2000 2001-2005 Mercedes-Benz CL-Class W215(CL600, CL550, CL55 AMG) car radio from Seicane with you. For more details, please click:

https://www.seicane.com/android-radio-hd-touchscreen-gps-navigation-for-1998-2005-mercedes-benz-cl-class-w215-cl600-cl550-cl55-amg-with-bluetooth-music-audio-aux-usb-wifi-steering-wheel-control-mirror-link-1080p-s6913g

Based on the advanced Android 8.0 operation system and a high-quality eight-core CPU processor, this all-in-one car radio can replace your factory radio because of its higher and better performance and configuration.

Thanks to the Bluetooth connection between your Bluetooth-enabled mobile phone and this unit, both Bluetooth hands-free phone calls and Bluetooth streaming music are available for you. So you can gain great convenience and entertainment.

Additionally, thanks to the worldwide real-time GPS navigation system, you are able to know where you are currently and get the most suitable route option to reach your desired destinations. And this unit comes with dual zone function, which enables you to listen to your favorite music while navigating.

If you like this car radio, don’t hesitate to add it to your shopping cart. Good luck!