There is no doubt that among lots of ways to upgrade your car’s capabilities and performance, the most popular way is to remove your factory radio and install a brand new multifunctional car radio in your car. With such an ideal car radio in your car, you can get access to a wide range of practical and entertainment features so as to enrich your in-car life. The following is a 2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008 car radio installation guide from Seicane, which can be taken as a reference for you if you have the same or similar dashboard.
Before and during installation, you should notice:
1. Before connecting,please make sure the ignition is off to avoid short circuit.
2. Ensure connect the yellow and red power cable at last.
3. Ensure that all loose wires are isolated with electrical tape
4. Ensure don’t tangle the wire when tighten the moving parts(Such as seat rails).
5. Ensure that all ground is connected to the same place.
6. Using the improper fuse may cause damage of fire,so when replace the fuse, please consult the professional.
7. For your convenience, here’s there commended tools for removal and installation from Seicane, please check for more details: http://www.seicane.com/car-dvd-dismantling-device-srd-400
2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008 car radio installation guide
1. The original car radio.
2. Use a plastic knife to pry the trim panel and remove it.
3. Remove screws that are holding the radio.
4. Take out the original car radio.
5. Disconnect the connectors and cables at the back of the radio.
6. Check all the accessories for the new Seicane car radio.
7. Connect the harnesses to the back of the new Seicane car radio.
8. Connect the Seicane car radio to your original radio’s plugs.
9. Turn on the new Seicane car radio to have a careful check if everything works well. If it doesn’t, please check whether all the cables are connected correctly.
10. Put the new Seicane car radio into the dash.
11. Put everything into their original place. All the installation is done.
That’s all about how to remove and install the new car radio for 2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008. If you meet any problems before or during the installation, please don’t hesitate to contact your dealer, communicate with someone experienced or turn to a professional for help. If you are afraid of failing in the installation, you can directly arrange a professional technician to help you install the new car radio. Anyway, it is very essential for you to pick an ideal car radio for your beloved car. Here I would like to share an amazing 2010 2011 2012 2013 2014 2015 Mitsubishi ASX Peugeot 4008 car radio from Seicane with you. You may click the following link for more details.
This car radio is running on the most advanced Android 6.0 operation system and a powerful quad-core CPU processor to enhance its capabilities and performance. Therefore, with this car radio installed in your car, you will be able to embrace much smoother, faster and easier operation experience.
With this car radio installed in your car, you will enjoy a lot of practical and entertainment features, mainly including high-end 3D GPS navigation system, FM/AM radio tuner, Bluetooth hands-free phone calls, Bluetooth streaming music, file management, etc. Thanks to these features, you are able to have a more convenient and relaxing driving experience.
Under the guidance of the turn-by-turn directions and voice prompts provided by the high-end 3D GPS navigation system, you are able to easily locate where you are and find the right way to reach any locations you would like go to go without getting lost any longer. And while navigating, you can also listen to your favorite music.
If you like this unit, just add it to your shopping cart right now. Good luck!
I have a problem with plugging into the Mitsubishi ASX. After all components have been connected, the airbag defect control indicator illuminates. Probably the problem is in the passenger airbag indicator. I not need to plug in a red cable that is attached on a cable harness for warning lights ?
If yes. Where?
“Dear,
so sorry for the inconvenience.
In order to give you a fast solution,we suggest you asked our after sales staff for help.
The email is Sales1@seicane.
Have a good day!”
Did u get help with the airbag light, i have the same problem.
“Dear,
so sorry for the inconvenience.
In order to give you a fast solution,we suggest you asked our after sales staff for help.
The email is [email protected]
Have a good day!”
I have bought a 2014 Mitsibushi ASX touch screen radio and want to install it in my 2012 Mitsibushi asx . I have the face plate and the green PC Board and if i replace the pc board everything light on the dash board goes out. When I plug the radio in every light on the dash board come on and the ref counter and the speedometer dies and the engine wont start properly. Is there something I an not doing right or is there some cables and other install kit i need to get to have this system working? Please help because had the car at an installer but does the same thing. Does the computer in the need to recognize the new radio or not?
Kind regards
Willem
“Dear,
so sorry for the inconvenience.
In order to give you a fast solution,we suggest you asked our after sales staff for help.
The email is [email protected]
Have a good day!”